Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
33333Insert the cassette with the exposed tape facing left. Tape direction is automatically set to “ FWD ”. 44444Press [[REC/ J]. A B C D RQT5717 16 Listening operationsRecording operations A B D C 2Normal tape High position tape To re-record Discrimination hole Tab for side B Tab for side A Side A 314FWD PLAY FWD Cassette tapes To fast-forward or rewind the tape Press [44444/REW/ g] or [33333/FF/ f] in the stop mode. To rewind To fast-forward 44444/REW/ g 33333 /FF/ f To find the beginning of a program (TPS: Tape Program Sensor) Press [44444/REW/ g] or [33333 /FF/ f] during play. Press the button once for each track to be skipped (up to 9 tracks). Backward Forward 44444/REW/ g 33333 /FF/ f Note TPS searches for silent parts of about 4 seconds normally found between tunes. As a result, it may not function properly in the following cases. • With short silent parts. • When noise occurs between tunes • With silent parts found within tunes Before recording Types of tapes which can be recorded correctly The system automatically identifies the type of tape. This system cannot correctly record or erase metal position tapes. Erasure prevention The illustration shows how to remove the tabs to prevent recording. To record on the tape again, cover as shown, being careful not to cover the high position discrimination hole. The effect of volume, sound quality, and sound virtualizer on recording. These have no effect on recording. They can be changed for playback. To erase a recorded sound 11111Press [STOP L]. 22222Press [REV MODE] on the remote control to select the reverse mode. 33333Insert the cassette with the exposed tape facing left. Tape direction is automatically set to “ FWD ”. 44444Press [[REC/ J]. A B C D RQT5717 16 Listening operationsRecording operations NORMAL POSITION/TYPE I 3 HIGH POSITION/TYPE II 3 METAL POSITION/TYPE IV 5 1 2 3 C B TAPE TAPE STOP TUNE MODE 1 2 3 4 5 6 7 9 0 10 CANCEL AUTO OFF SLEEP 8 PROGRAM TUNE MODE PLAY MODE REV MODE SELECTOR TAPE TUNER CD CLOCK TIMER PLAY REC REWCLEAR FF BASS TREBLE REV MODE 2 FWD PLAY FWD REV PLAY REC MHz FWD REC FWD side to be recorded facing up and " " automatically changes to " is pressed. 3 (unneccessary with auto editing recording, \Page 19) Set the tape direction. FWD : To record on the forward side. REV : To record on the reverse side. To change the direction Press [TAPE 2 3] twice and then [STOP L]. Preparation: Do the preparatory steps above. 1 Tune to the required station. (\page 10 or 11) 2 Press [[REC/ J] to start recording. To stop recording. Press [STOP L]. To stop recording temporarily Press [[REC/ J]. To resume recording, press [[REC/ J]. by remote control only C To reduce noise while recording an AM broadcast (Beat proof function) Press and hold [TUNE MODE] while recording. Every time you press and hold the button: BP 1 « BP 2 Select the position where there is less noise. : Both sides record (forward reverse). " when ([REC/J) Recording operations B Recording the radio RQT5717 17 A 2 1 3 Before recording A Preparatory steps Do these steps before each recording. Wind up the leader tape so recording can begin immediately. (unneccessary if auto CD editing) Preparation: Press [POWER ] to turn the unit on. 1 Insert the tape to be recorded on. Insert with the exposed tape facing left. 2 Press [REV MODE] on the remote control to select the reverse mode. Every time you press the button: : One side only records. Recording CDs Normal recording Recording operations 1 2 3 4 5 2 REV MODE SELECTOR REC OPEN/CLOSE 3 11 4 5 FWDREC FWD FWD side to be recorded facing up Tape direction FWD • Tracks are recorded in the order in which they are found on the CD. • Tracks are cut in the middle when the end of the tape is reached. • You can record from any point on the tape. 1 Insert the cassette with the exposed tape facing left. Tape direction is automatically set to “ FWD 2 Press [REV MODE] on the remote control to select the reverse mode. Every time you press the button: ” : One side is recorded. , 3 Press [SELECTOR] to select the CD mode. 4 Press [OPEN/CLOSE c] to open the CD tray. Insert the CD with label facing upward. Press [OPEN/CLOSE c ccccc] to close the CD tray. 5 Press [[REC/ J] to start recording. • If you selected “ ” in step 2, the direction will automatically change to “ ” when recording starts. • The recording will start from the first track. To stop recording Press [STOP L]. The recording and the CD will stop. To stop recording temporarily Press [[REC/ J]. To resume recording, press [[REC/ J]. To record on reverse side Before recording, press [TAPE 2 3] twice and immediately thereafter [STOP L]. The tape direction will be shown as “ REV ”. To record from a specific point on a tape Before recording, advance the tape to the point from where you want to start recording. To record programmed tracks 1 11111After step 4, program the track(s) you want (\steps 2-4 on page 14). 2 22222Press [[REC/ J] to start recording. 18 RQT5717 Recording CDs You can record the ...