Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
The turntable PLATTER (2) will start to spin. 7. Push the CUE LEVER (19) to the "UP" position. Page 4 8. Position the tone arm over the desired groove on the record and push the CUE LEVER (19) to the "DOWN" position. The TONE ARM (5) will slowly lower onto the record at which time play will begin. 9. When play is over, raise the TONE ARM (5), move it to the ARM REST (9), and secure it with the ARM CLAMP (8). 10. You now have the option of turning off the power by turning the POWER SWITCH (15) to the "OFF" position, or stopping the PLATTER (2) by pushing the START STOP BUTTON (16) and engaging the electronic brake. B. INTERRUPTING PLAY 1. Pushing the CUE LEVER (19) to the "UP" position will cause the TONE ARM (5) to lift stopping play. 2. Pushing the CUE LEVER (19) to the "DOWN" position will cause the TONE ARM (5) to slowly lower onto the record at the point where play was interrupted. C. PLAYING 45 RPM RECORDS 1. When playing a 45 rpm record with a large center hole, first place the 45 ADAPTOR (20) on the center spindle. 2. Be sure that the 45 SPEED SELECTOR BUTTON (18) is pushed and the 45 SPEED INDICATOR (17) is illuminated. D. TARGET LIGHT 1. Firmly pushing the TARGET LIGHT SWITCH (21) will cause the TARGET LIGHT (22) to raise into position and illuminate the stylus tip. If you don't push the TARGET LIGHT SWITCH (21) firm enough, the TARGET LIGHT (22) will turn on but will not raise high enough to illuminate the stylus tip. 2. To lower the TARGET LIGHT (22) push down on it until it locks in the casing. 3. When not being used, the TARGET LIGHT (22) should be kept in the lowered position. E. XLR LAMP ADAPTOR 1. Plug a gooseneck light with an XLR base, like the GEMINI GNL-500, into the XLR LAMP ADAPTOR (23). 2. When the power is turned on, the light will illuminate. F. ADJUSTING THE PITCH CONTROL 1. The XL-1800QIV is equipped with a PITCH CONTROL (24) and Quartz locked speed When the PITCH CONTROL (24) is in the center position and the PITCH LED (25) lights GREEN, the Quartz lock is activated and the speed will be exactly 33 or 45 depending on which SPEED SELECTOR BUTTON (18) is pushed. 2. When the PITCH CONTROL (24) is positioned off center, the PITCH LED (25) will light RED and the pitch can vary +/- 8% depending on the position of the PITCH CONTROL (24). 3. The PLATTER (2) is equipped with a STROBE RPM INDICATOR STRIP (26) and the POWER SWITCH (15) contains built in STROBE LIGHTS (27). When the PLATTER (2) is spinning, the STROBE LIGHTS (27) illuminate the STROBE RPM INDICATOR STRIP (26). The bottom row of dots will appear to be stationary when the speed of the platter is exactly 45 RPM. The second row from the bottom will appear to be stationary at 33 RPM. G. ARM-LIFT HEIGHT ADJUSTMENT 1. If the pre-adjusted distance that the CUE LEVER (19) raises the stylus off the record surface is inadequate, it can be adjusted by turning the ARM-LIFT HEIGHT ADJUSTMENT SCREW (28) while simultaneously pushing down on the TONE ARM (5). Clockwise rotation of the screw will decrease the distance and counter clockwise rotation will increase the distance.. TURNTABLE SECTION: Type............................Quartz Direct Drive Manual Turntable Drive Method......................................................Direct Drive Motor..............................................Brushless DC Motor 24V Platter...................Aluminum Diecast 11 1/2" (292mm) Dia. Weight...............................2 lbs. (0.9 Kg) Speed........................................................33 1/3 or 45 RPM Starting Torque.......................................1.5 Kg/cm (1.3 lb/in) Build-up Characteristics......0.7 sec. standstill to 33 1/3 RPM Braking System..........................Electronic Brake (Solenoid) Wow and Flutter.............................................0.01% WRMS* * This rating refers to the turntable assembly and platter only and excludes effects of records, cartridges or tonearms. Rumble.....................................................56 dB Unweighted TONEARM SECTION: Type..................................Universal S-Shaped Tubular Arm Effective Length......................................9 1/16’ (230.1 mm) Arm Height Adjust Range........................................0 - 6 mm Overhang...................................................19/32" (15.2 mm) Effective Mass...................................9 g (Without Cartridge) Offset Angle.....................................................................22° Friction.............................Less Than 7 mg (Lateral, Vertical) Tracking Error Angle............Within 2°32' at the outer groove and within 0°32' at the inner groove of a 30 cm (12") record. Stylus Pressure Adjust Range..................................0 - 2.5 g Applicable Cartridge Weight Range...........................6 -10 g Headshell Weight..........................................................5.6 g GENERAL: Power Supply...................................