Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
BII 24550 (0209) 08B26-S3V-2000-91 1 of 7 TOOLS AND SUPPLIES REQUIRED Flat-tip screwdriver Phillipsscrewdriver Ratchet 8 mm, 10 mm, and 12 mm Sockets Shop towel Diagonal cutters 8 mm and 10 mm Combination wrenches INSTALLATION 4. Remove the screws fastening the audio brackets, then pull the audio unit out toward you. Unplug the vehicle connectors and antenna lead from the rear of the audio unit. Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.” 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 3. Using a flat-tip screwdriver wrapped with a shop towel, pry up on the clips and pull the radio panel out toward you. Unplug the connectors and remove the radio panel. RADIO BRACKET ANTENNA LEAD VEHICLE HARNESS SCREW 5. On the driver’s side of the vehicle, gently pull the center console lower cover out toward you to release the clips and remove the center console lower cover. Take care not to damage the clips. RADIO PANEL CLIP CENTER CONSOLE LOWER COVER DRIVER’S SEAT CLIP 2 of 7 BII 24550 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved. 6. Remove the driver’s seat front cover by pulling it toward you. Take care not to damage the clips. DRIVER’S SEAT DRIVER’S SEAT FRONT COVER CLIP 7. Route one end of the BUS cable from the radio opening down through the center console. FRAME RADIO OPENING VEHICLE HARNESS BUS CABLE 14-PIN CONNECTOR BUS CABLE BUS CABLE 8. Continue routing the BUS cable along the center console and the driver’s seat. 9. Locate the slit in the floor carpet just under the driver’s seat cushion, and pull the BUS cable 14-pin connector out about 300 mm through the slit. SLIT in FLOOR CARPET about 300 mm BUS CABLE DRIVER’S SEAT 10. Secure the BUS cable to the vehicle harness with a wire tie in the area shown. BUS CABLE VEHICLE HARNESS TAPE WIRE TIE © 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24550 (0209) 3 of 7 11. At the radio opening, adjust the BUS cable so it's the same length as the vehicle harness. Make the BUS cable and vehicle harness are the same length. WIRE TIE WIRE TIE VEHICLE HARNESS BUS CABLE BUS CABLE BLACK CUSHION TAPE 12. Secure the BUS cable to the vehicle harness with three wire ties in the areas shown. 13. Attach the black cushion tape at the edge of the center console in the area shown. 14. Install the right and left base brackets into the holes in the driver’s seat risers, and install two 6 x 12 mm flange bolts into each bracket. Do not tighten the bolts yet. 6 x 12 mm FLANGE BOLTS (4) LEFT BASE BRACKET RIGHT BASE BRACKET 4 of 7 BII 24550 (0209) © 2002 American Honda Motor Co., Inc - All Rights Reserved. Installing the CD Changer 15. Carefully unpack the CD changer. Remove the three shipping clips, and discard the shipping cover. Install an adhesive seal (included with the CD changer kit) over each of the three clips holes. Save the shipping clips for your customer in the event the unit needs to be serviced. SHIPPING CLIPS (3) SHIPPING SEALS (3) SHIPPING COVER (Discard.) 16. Visually check the position of the spring adjusting pin on both sides of the CD changer. If the spring adjusting pins are not in the horizontal (H) position, move the pins to the horizontal (H) position by sliding them up with an awl. SPRING ADJUSTING PIN LEFT LOCKING COVER (included with CD Changer kit) RIGHT LOCKING COVER (included with CD Changer kit) SPRING ADJUSTING PIN (H: Horizontal) (V: Vertical) 17. Remove the adhesive backing from the “L” and “R” locking covers, and attach them to the sides of the CD changer. Align the diagonally opposite holes with the H and V positions. 18. Install the right changer bracket on the CD changer using two 4 x 8 mm washer-screws, and the two wire clips. Install the left changer bracket on the CD changer using two 4 x 8 mm washer-screws. NOTE: With the changer mounted in this location, the locking covers do not indicate right and left correctly. Mount the CD changer brackets in the direction shown. RIGHT CLIP CHANGER BRACKET 4 x 8 mm WASHERSCREW WIRE LEFT CHANGER BRACKET 4 x 8 mm WASHER- SCREW WIRE CLIP FRONT © 2002 American Honda Motor Co., Inc - All Rights Reserved. BII 24550 (0209) 5 of 7 19. Attach one gray cushion tape to the rear of the CD changer leaving half of the cushion tape extended past the CD changer. Using scissors, cut the cushion tape at the end of the CD changer. Fold the ends down around the edges of the CD changer. LEFT BASE BRACKET RIGHT BASE BRACKET FLANGE NUT CD CHANGER GRAY CUSHION TAPE GRAY CUSHION TAPE 20. Attach the other gray cushion tape to the CD changer overlapping the other cushion tape. Fold the cushion tape around the CD changer bracket. 21. Position the CD c...