Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
3 LOCATION OF CONTROLS 1) DUST COVER 2) LEFT SPEAKER 3) DIAL SCALE 4) TUNING KNOB 5) FUNCTION SELECTOR (PHONO/AM/FM/FM STEREO) 6) FM STEREO INDICATOR 7) RIGHT SPEAKER 8) POWER ON/OFF AND VOLUME CONTROL 9) POWER LED INDICATOR 10) 45 RPM ADAPTOR 11) 33/45/78 RPM SPEED SELECTOR 12) TONE ARM CLAMP 13) AUTO STOP SWITCH 14) LINE OUT SOCKET 15) FM ANTENNA 16) AC CORD CAUTION: THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. PRECAUTIONS FOR USE • UNPACK ALL PARTS AND REMOVE THE PROTECTIVE MATERIAL. • DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE. • DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL INCHES AROUND THE UNIT FOR VENTILATION. POWER CONNECTION 1. CONNECT THE POWER CORD (16) TO A 120V AC ~ 60Hz OUTLET. 2. TURN ON THE POWER (8) BY ROTATING THE VOLUME CONTROL CLOCKWISE UNTIL A CLICK IS HEARD. IF THE POWER LED INDICATOR (9) IS ON WITH RED LIGHT, IT MEANS THAT THE POWER SUPPLY IS NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE MUSIC. LISTENING TO RADIO 1. SET THE FUNCTION SELECTOR (5) TO THE DESIRED RADIO BAND (AM, FM OR FM-STEREO). 2. TUNE TO THE REQUIRED STATION BY TURNING THE TUNING KNOB (4). 3. ADJUST THE VOLUME CONTROL (8) TO OBTAIN THE DESIRED SOUND LEVEL. FM & FM-STEREO RECEPTION • WHEN THE FUNCTION SELECTOR (5) IS SET TO THE “FM” POSITION, PROGRAMS ARE RECEIVED IN MONO MODE. IN PARTICULAR WHEN STEREO SIGNALS ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO. • SET THE FUNCTION SELECTOR (5) TO THE “FM-ST” POSITION FOR RECEIVING STEREO PROGRAMS. THE LED “ST” INDICATOR (6) WILL LIGHT UP WHEN A FM STEREO PROGRAM IS BEING RECEIVED. 4 HINTS FOR BEST RECEPTION: - AM: THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHTLY ROTATING OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION. - FM: THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA (15). THIS WIRE SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION. IF FM RECEPTION IS WEAK TRY REPOSITIONING THE FM WIRE ANTENNA UNTIL YOU FIND THE STRONGEST FM SIGNAL. PLAYING PHONO RECORDS 1. RAISE THE TURNTABLE DUST COVER. 2. REMOVE THE STYLUS PROTECTOR AND RELEASE THE TONE ARM CLAMP (12). 3. SET THE FUNCTION SELECTOR (5) TO “PHONO”. 4. PLACE A RECORD ON THE TURNTABLE, OVER THE CENTER SPINDLE. 5. SET THE SPEED SELECTOR SWITCH (11) TO 33, 45 OR 78 RPM ACCORDING TO THE RECORD YOU ARE PLAYING. PLACE THE INCLUDED 45 RPM ADAPTOR (10) OVER THE CENTER SPINDLE WHEN PLAYING 45 RPM RECORDS. 6. MOVE THE TONE ARM TO THE BEGINNING OF THE RECORD OR TO THE BEGINNING OF A PARTICULAR TRACK. GENTLY LOWER THE TONE ARM ONTO THE RECORD TO START PLAYING. 7. ADJUST THE VOLUME IF NEEDED. THE TURNTABLE WILL STOP AUTOMATICALLY WHEN THE RECORD FINISHES. 8. TO STOP THE RECORD BEFORE IT ENDS, LIFT THE TONE ARM AND RETURN IT CAREFULLY ONTO THE TONE ARM CLAMP (12). 9. REPLACE THE STYLUS PROTECTOR ON THE STYLUS WHEN NOT IN USE. IMPORTANT: I. DO NOT STOP OR TURN THE PLATTER MANUALLY. II. MOVING OR JARRING THE TURNTABLE WITHOUT SECURING THE TONE ARM CLAMP COULD RESULT IN DAMAGE TO THE TONE ARM. AUTO-STOP SWITCH OPERATION THE AUTO-STOP AREA ON SOME RECORDS MAY EXTEND BEYOND THE PRESET SETTING. AS A RESULT THE TURNTABLE COULD POSSIBLY STOP BEFORE THE LAST TRACK FINISHES. IF YOU EXPERIENCE THIS DURING PLAYBACK, SET THE AUTO-STOP SWITCH (13) LOCATED ON THE BACK OF THE UNIT TO THE “OFF” POSITION. THE TURNTABLE WILL NOW RUN TO THE END OF THE RECORD BUT WILL NO LONGER STOP AUTOMATICALLY. TO STOP THE TURNTABLE YOU WILL NEED TO EITHER SET THE FUNCTION SELECTOR (5) TO ANOTHER POSITION OTHER THAN PHONO OR RETURN THE AUTO-STOP SWITCH (13) TO THE “ON” POSITION. AFTER THE RECORD STOPS, LIFT AND RETURN THE TONE ARM CAREFULLY BACK ONTO THE TONE ARM CLAMP (12). 5 LINE OUT OPERATION FOR BETTER PLAYBACK SOUND, YOU CAN CONNECT THE SB6051 TO AN EXTERNAL AUDIO AMPLIFIER VIA THE RCA LINE OUT JACKS LOCATED ON THE BACK PANEL. PLEASE PROCEED AS FOLLOWING: 1. CONNECT THE “L” & “R” LINE OUT JACKS AND THE AUX IN OF YOUR AUDIO AMPLIFIER. (CONNECTION CABLE IS NOT INCLUDED). 2. SELECT THE MUSIC SOURCE BY SETTING THE FUNCTION SELECTOR (5) TO “PHONO”, “AM”, “FM” OR “FM ST” AS DESIRED. 3. TURN ON THE EXTERNAL AMPLIFIER. 4. SOUND WILL THEN COME OUT FROM THE SYSTEM’S BUILT-IN SPEAKERS AND THE EXTERNAL AMPLIFIER’S SPEAKERS SIMULTANEOUSLY. 5. SET THE VOLUME CONTROL (8) TO “MIN” AND ADJUST THE SOUND LEVEL USING THE VOLUME CONTROL ON THE EXTERNAL AMPLIFIER AS DESIRED. 6. TURN THE SYSTEM AND THE EXTERNAL AMPLIFIER OFF WHEN YOU HAVE FINISHED LISTENING. 7. UNPLUG THE CONNECTION CABLE. CARE AND MAINTENANCE CLEAN YOUR UNIT WITH A DAMP (NEVER WET) CLOTH. SOLVENT OR DETERGENT SHOULD NEVER BE USED. 1. AVOID LEAVING YOUR UNIT IN DIRECT SUNLIGHT OR IN HOT, HUMID OR DUSTY PLACES. 2. KEEP YOUR UNIT AWAY FROM HEATING APPLIANCES AND SOURCES OF ELECTRICAL NOISE SUCH AS FLUORESCENT LAMPS OR MOTORS. 3. ALWAYS CLEAN THE OUTSIDE OF THE CABINET THOROUGHLY IF IT BECOMES WET WITH MOISTURE OR WATER SPLASHES. THIS WILL HELP TO PROTECT THE...