Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
6. Inset the headshell into the front end of the tonearm, then turn the lock nut counterclockwise clockwise with the headshell firmly held horizontally. 7. Slide counterweight onto tonearm. Twist it lightly and it will screw onto the rear shaft of the tonearm. 8. Adjustment of horizontal zero (0) balance and stylus pressure: (a) Remove the stylus protector, do not touch the stylus tip during the adjustment. (b) Set the cueing lever to the lower position. (c) Release the arm clamp and lift the tonearm from the arm rest to free it. (d) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely). (e) Refasten the tonearm with the arm clamp. (f) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number “o” of the ring into alignment with he center line on the tonearm rear shaft. (g) Rotate the counterweight counterclockwise until the scale shows the value corresponding to the pressure of the used stylus. The stylus pressure of the installed pick-up system is 2g. Should you use a separate pick-up system, please follow the manufacturer’s instruments. 9. Set the anti-skating control knob to the same value as the stylus pressure. 10. Install the dust cover to the main unit. Placement • Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. • Do not place the unit in a location where there is high humidity or a lot of dust. • Cartridge may pick up slight sound pressure or vibrations of the speakers coming along the floor or though the air resulting in howling. Find a location which is very stable and vibration free. • The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body horizontally. Connections 1. Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. 2. Connect the unit output terminals to the the PHONO jack of your American DJ Mixer or receiver. Output terminals Mixer (Receiver) L (White) (19) ---------------------------->L Channel R (Red) (18) -----------------------------> R Channel GND (Spade) (20) ---------------------> Ground NOTE: Be sure to connect the ground terminals firmly to the Mixer or receiver. If this connection is not made or is loose, a power source “HUM” will result. TTB-2010 User Instructions page 3 User Instructions Operation 1. Push the power button (4) to turn on the power, the speed indicator (8) and the strobe-illuminator will light up. 2. Place a record on the slipmat. When playing a 45-rpm record with a large center hole, place the 45-rpm adapter (1) on the center spindle. 3. Set the speed (10) to match the record. 4. Remove the stylus protector, release the arm clamp. 5. Set the cueing lever to the up position. 6. Press the Start/Stop button (5), the turntable platter will start to rotate. 7. Move the tonearm (13) over the desired groove. 8. Set the cueing lever to the down position, the tonearm will descend slowly onto the record and begin playing. 9. When play is finished, raise the cueing lever, move the tonearm with arm clasp. 10.Press the Start/Stop Button (5) to stop the platter from rotating. Push the Power Button (4) to turn off the power. • SUSPEND PLAY - Set the cueing lever to “UP” position during play, the stylus tip of the cartridge will be lifted from the record. • TARGET LIGHT - This unit provides a target light (7) for illuminating the stylus tip during play. After pushing the target light button, the target light will be raised into position for illuminating the stylus tip. When not in use, keep the target light lowered. Changing the Speed • As long as the pitch control (12) is in center click position, the turntable is operated at quartz controlled rated speed. • The speed can be increased or decreased by 10% by the pitch control (12). An incorrect adjustment done on purpose can also be used to have the turntable rotate extremely slow or fast. The strobe dots (5) at the edge of the turntable are used for speed monitoring. Remote Control Start/Stop (21) • The Start/Stop function can remotely be controlled by a separate switch via a mixing console with a “Fader Start” function. Activated the “Fader Start” on the mixing console and the turntable automatically begins Start/Stop. Future American DJ mixers will be equiped with the “Fader Start” function. Maintenance • Clean the stylus periodically with a soft brush to prevent the accumulation of dust. • When sound becomes distorted or noisy, check the stylus. If the stylus is worn out, replace it with a new one. • From time to time, the dust cover and turntable cabinet should be wiped down with a soft, dry cloth. • Volatile materials should not be used, such as: alcohol, thinner, benzine etc. They may remove the paint or damage the luster. Specifications • Power Supply: AC 115V/60Hz, or 230V/50Hz • Power Consumption: 8W • Dimensions (WxDxH): 17.5” x 13 ...