Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
When the power is turned sound. on, the DEMO display is overridden by the operation display. Press the T-BASS button., When the power is turned off, the DEMO mode is restored. Each time it is pressed, the level changes. Select one of the three levels, or the off position to suit your preference. To cancel DEMO mode Press the II SET button while the power is off. The clock &+l++2~+3~oFF (cancel)~ flashes on the display. (To set the current time, see “SETTING I THE CLOCK on page 15.) To re-activate DEMO mode, press the -button while the power is off. Flash window The window on the top of the unit lights up or flashes while the To select with the remote centrol unit is being powered on. press the T-BASS button while pressing the SHIFT button. To turn off the light of the top window, press the CD button while pressing the n button. To turn back on, repeat the above. m Low frequency sound may be distorted when the T-BASS system To turn the unit off is used for a disc or tape in which low frequency sound is Press the POWER button. originally emphasized. In this case, cancel the T-BASS system. Using the headphones Connect headphones to-the PHONES jack with a standard stereo plug (06.3 mm, ‘/4 inch). No sound is output from the speakers while the headphones are plugged in. Sound adjustment during recording The output volume and tone of the speakers or headphones may be freely varied without affecting the level of the recording. 5 ENGLISH GRAPHIC EQUALIZER This unit provides the following three different equalization curves. ROCK: Powerful sound emphasizing treble and bass POP: More presence in the vocals and midrange JAZZ: Accented lower frequencies for jazz-type music. Press one of the GRAPHIC EQUALIZER buttons. To cancel the selected mode Press the selected button again. ‘(EQ oFF” is displayed. To select with the remote control Press the GEQ button repeatedly while pressing the SHIFT button. The GEQ mode is displayed cyclically as follows. ROCK — POP — JAZZ — EQoFF (cancel) MANUAL TUNING MONO TUNER BAND SHIFT -==-J u 1 Press the TUNER/BAND button repeatedly to select the desired band. L–-.----~ When the TUNER/BAND button is pressed while the power is off, the power is turned on directly. To select a band with the remote control Press the BAND button while pressing the SHIFT button. 2 Press the 4+ DOWN or > UP button to select a station. Each time the button is pressed, the frequency changes. When a station i$ received, “TUNE is displayed for 2 seconds. During FM stereo reception, (1[~1}] is displayed. To search for a station quickly (Auto Search) Keep the 44 DOWN or -UP button pressed until the tuner starts searching for a station. After tuning in to a station, the search stops. To stop the Auto Search manually, press the 4 DOWN or _ UP button. The Auto Search may not stop at stations with very weak signals. When an FM stereo broadcast contains noise Press the MONO TUNER button while pressing the SHIFT button on the remote control so that “AU”TO disappears on the display. Noise is reduced, although reception is monaural. To restore stereo reception, press these buttons so that “AUTO” appears. To change the AM tuning inte!rval The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where the fr6quency allocation system is 9 kHz/step, change the tuning interval. Press the POWER button while pressing the TUNER/BAND button. To reset the interval, repeat this procedure. m When the AM tuning interval is clhanged, all preset stations are cleared. The preset stations have to be set again. ENGLISH 6 PRESETTING’STATIONS The unit can store a total of 32 preset stations. (Each, band has a maximum of 20 available preset stations.) When a station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station directly. 1 Press the TUNEFUBAND button to select a band, and press the + DOWN or -UP button to select a station. 2 Press the 1I SET button to store the station. A preset number beginning from 1 in consecutive order for each band is assigned to the station. Frequency Preset number , 3 Repeat steps 1 and 2. The next station will not be stored if a total of 32 preset stations for all the bands or a total of 20 preset stations for one band have already been stored. PRESET NUMBER TUNING Use the remote control to select the preset number directly. 1 Press the BAND button while pressing the SHIFT button to select a band. ‘ 2 Press the numbered buttons to select a preset number. Example: To select,preset number 20, press the +1O,+1Oand Obuttons. To select preset number 15, press the +10 and 5 buttons. Selecting a preset number on the main unit Press the TUNER/BAND button to select a band. Then, press the P PRESET button repeatedly. Each time the button is pressed, the next ascending number is selected. To clear a preset station Select the preset number of the station to be cleared. Then, press the n CLEAR button, and press the II SET button within ...