Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle. Important Note This DVD player incorporates two new features: 1) A wireless FM Modulator 2) Capability to add an optional plug in TV tuner (Audiovox P/N PODTVT – must be ordered separately) Please be advised that the wireless modulator will perform well in most applications. However, in certain applications the quality of the wireless signal may be less than optimal, resulting in static or strong local station bleed thru. If this is the case, an optional relay box is available. The Audiovox part number is SIRSWB and plugs into the 1/8" jack on the side of the chassis. This relay box is installed between the vehicle antenna and the car radio to provide the best possible FM reception of the DVD player audio. When the SIRSWB is installed it is recommended that the wireless FM antenna that is plugged into the printed circuit board next to the 3.5mm jack be unplugged. See page 6 of this manual for additional information. MATERIALS INCLUDED IN THIS PACKAGE: 1) ADV350 TV/Video Monitor with DVD (1pc) 2) 12 Pin Power / Signal harness (P/N 112-3483) (1 pc) 3) 2 Pin Power Wire Harness with choke (P/ N 112B3143) (1 pc) 4) Hardware Package #4 x 3/8” Screws (9 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 5) Remote Control (1363855) (1pc) 6) PODTVT TV Tuner (P/N 136-3877) (1pc) (Optional) 7) SIRSWB Relay Box (P/N 112C3159) (1pc) (Optional)-See important note on previous page 8) Trim Ring (1pc) 9) Game Controller (P/N 136-3982) (1pc) TOOLS REQUIRED: #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe) Marker pen – to mark headliner Scribe (to mark trim ring if used) Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from vehicle to vehicle) DVD Movie (to verify system operation after installation) 1 2 3 5 64 IRTA ON/OFF ON/OFF IRTB 7 8 (Optional) (Optional) SOURCE 9 1 2 3 5 64 IRTA ON/OFF ON/OFF IRTB 7 8 (Optional) (Optional) SOURCE 9 -1 GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting wire harnesses will need to be located. If any access holes need to be cut into the vehicle (headliner, other trim compo...
Эта инструкция также подходит к моделям:Мониторы - ADV350P (82.49 kb)
Мониторы - ADV350B (82.49 kb)
Мониторы - ADV350S (82.49 kb)
Мониторы - ADV350P (82.49 kb)