Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door. NOTE: Because radio control devices are inherently susceptible to RF interference, this product should NOT be used as a stand-alone security device. This product is considered a monitoring and notification device ONLY, and as such, should not be used as a substitute for a dedicated home security system. To ensure that your Garage Door Monitor continues to operate properly, the following checks should be performed on a monthly basis: • Check that the sensor is mounted properly on the garage door (see Mounting the Sensor section of this manual.) • Ensure the 3 volt lithium battery is installed properly. • Check to see that the receiver system is plugged into a wall outlet and the jack is properly connected to the back of the receiver. Make sure the antenna is straight and not in contact with any metal objects. • Check that the receiver is properly recognizing sensor signals (see Troubleshooting section of this manual.) INSTALLING THE BATTERY IN THE GARAGE DOOR INDICATOR SENSOR 1. Place the screw driver blade on the tab at the end of the case and gently press down and in toward the case. 2. Insert the the lithium battery into the battery clip with the + (positive) side face up. 3. Push the case back together tightly by inserting the top hooks into the back cover, then snap shut the bottom of the case. NOTE: It is normal to hear a rattle from the tilt switch in the sensor when tilted or rotated to another position. 3VOLTS INDOOR RECEIVER SETUP 1. Plug the AC adapter into any standard 110 volt AC electrical wall outlet and the small plug into the back of the indoor receiver. 2. The receiver has a 9" antenna wire which comes out the back. The antenna should be straight and not touching metal. CLOSED OPEN Antenna Learn Button AC Adapter Location Know when your garage door is openor closed! Thank you for purchasing the LiftMaster Garage Door Monitor. Monitor the status of your garage door from inside your home. No longer will you have to run downstairs or go outside just to see if you or your children have left the garage door open. CLOSED OPEN AC AdapterSensor CR2032 3 VOLTS Lithium Battery Double-Sided GARAGE DOOR MONITOR SYSTEM (CR2032 type) Fastening Strip Indoor Receiver PRE-INSTALLATION SYSTEM TEST 1. The sensor and receiver are pre-matched (programmed) at the factory. Test the system by flipping the sensor over while it is a few feet away from the receiver. The receiver will show a green light for closed when the sensor is face up in the vertical position with the round end of the case pointing down (Figure 1). The red light will flash when the sensor is face down in the horizontal position (Figure 2). 2. If the green or the red receiver lights do not come on, or do not react as described, see the Troubleshooting or Learning section of these instructions. Figure 1 Figure 2 MOUNTING THE SENSOR Attach the sensor to the inside of the garage door using the double-sided fastening strip. Mount the sensor near the top of the garage door for best results. The round end of the case should be pointing down when the garage door is closed. Inside of Garage Double-Sided Fastening Strip Round End Down GARAGE DOOR MONITOR OPERATION TROUBLESHOOTING When the receiver is powered up, both red and green LED’s will blink once. The receiver will then show a solid green LED until it receives a signal from a programmed sensor. The receiver will display the current status of the programmed door sensor. If no door sensor(s) is programmed to the receiver, the green and red LED will flash simultaneously. See Learning section. The sensor sends a closed signal when the garage door is closed (vertical) and an open signal as the sensor changes to open (horizontal) position. Up to 4 door mounted sensors will work in conjunction with one receiver. The red LED will blink once every half-second if one or more of the programmed sensors are not in the closed position. The green LED comes on steady only when all the programmed sensors are in the closed position. NOTE: The system will sometimes take a few seconds to send a signal. The sensor updates the receiver by transmitting an open or closed signal every few minutes. LEARNING MORE THAN ONE SENSOR(S) 1. Door must be closed and the green LED on steadily. 2. Press and hold the learn button for 2 seconds, the receiver will enter the learn mode. The green LED will blink on and off in 1/2 second increments. 3. The additional sensor(s) must be moved from a vertical position to a horizontal position or vice versa. Press and Hold the Learn Button 4. Both green and red LED’s will turn on for 1 second to indicate a successful learn. Upon success, the receiver immediately exits the learn mode and returns to normal operation. 5. If no signal is received within 30 seconds, the receiver will exit the learn mode and return to normal operation. ERASING OR CLEARING THE MEMORY 1. Unplug the small...