Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
PBP 960x1080 10 : 960x540 PIP 0 : 480x270 < 1920x1080 > Picture ID 2 If you press the left/right buttons or press the ON button repeatedly, the Picture ID cycles through OFF and 1 to 4. Assign the ID you want. Picture ID is used to change the settings of a specific display using a single IR receiver for multi-vision. The set receiving the IR signal communicates with another set via an RS232 connection. Each set is identified by a Set ID. If you assign the Picture ID using the remote control, only displays with the same Picture ID and Set ID can be controlled remotely. Picture ID . Off . Close AUDIO(RGB/DVI) REMOTECONTROL INRS-232C OUTRS-232C INRS-232C OUTRS-232C INRS-232C OUTRS-232C IN AUDIO(RGB/DVI) REMOTECONTROL INRS-232C OUTRS-232C INRS-232C OUTRS-232C INRS-232C OUTRS-232C IN yyIf you assign the Set ID to each set with multi-vision, and then assign the Picture ID using the red button on the remote control, the key command is displayed for the set with the same Set ID and Picture ID. A set with different Set IDs and Picture IDs cannot be controlled by IR signals. yyThe maximum value of the Picture ID can be set in the Total Set ID menu. yyPlease refer to the Installation Manual for more information on Total Set ID assignment. IR Receiver Picture ID < Off > Close NOTE yyFor example, if the Picture ID is assigned to 2, the upper right display (Set ID: 2) can be controlled by IR signals. yyFor each set, you can change the settings for the PICTURE, AUDIO, TIME, NETWORK and MY MEDIA menus or the hot keys on the remote control. yy If you press the green OFF button for Picture IDs, the Picture IDs for all sets are turned off. If you then press any button on the remote control, all sets will start working again. yyPicture ID will be disabled while using the MY MEDIA menu. yyIf Picture ID is set to Off, holding buttons on the remote control will execute only one action at a time. 2X2 Multi-Vision (Total Set ID: 4) Set IDs are assigned as shown in the picture. 1 Press the red ON button on the remote control to assign the Picture ID. NETWORK Settings 1 Press SETTINGS to access the main menus. 2 Press the navigation buttons to scroll to NETWORK and press OK. 3 Press the navigation buttons to scroll to the setting or option you want and press OK. - To return to the previous level, press BACK. 4 When you are finished, press EXIT. When you return to the previous menu, press BACK. NETWORK Move OK . • Player Name Setting • Network Setting : None • Network Status : Not connected • Server IP Setting • Server IP Status : Not connected The available option settings are described in the following: Setting Description Player Name Setting Sets the player name used in SuperSign Manager.(Up to 20 characters) Network Setting Configure the network settings. Network Status Display the network status. - Internet is connected : Extermally connected - Network is connected : Only internally connected - Not connected : When there is no network connection Server IP Setting Sets the IP address of the computer (server) on which SuperSign Manager is installed. Server IP Status Displays the connection status with the server. - Not connected : When there is no network connection with SuperSign server - Waiting for approval : When network connection with SuperSign server has been made, but access to server has not been approved by the server - Rejected : When network connection with SuperSign server has been made, but access to server has been rejected by the server - Internet is connected : When network connection with SuperSign server has been made and access to server has also been approved by the server CAUTION yyWhen setting the Player Name, input delay may occur if you press the buttons on the remote control continuously. 54 MAKING CONNECTIONS ENGLISH ENG MAKING CONNECTIONS Connect various external devices to the ports on the monitor set’s back panel. 1 Find an external device you want to connect to your monitor set shown on the following illustration. 2 Check the connection type of the external device. 3 Go to the appropriate illustration and check the connection details. HD Receiver VCR DVD HDMI DVI AV Component AV Component HDMI DVI AV Component Speaker USB Memory storage PC Gaming device Camcorder/Camera HDMI AV Component HDMI DVI AV Component HDMI DVI RGB LAN Display Port NOTE yyIf you connect a gaming device to the monitor set, use the cable supplied with the gaming device. yy47WV50BS is not supporting composite(AV) signal & input. 55 MAKING CONNECTIONS ENG ENGLISH HDMI Connection Transmits the digital video and audio signals from an external device to the monitor set. Connect the external device and the monitor set with the HDMI cable as shown on the following illustration. Connecting to a HD Receiver, DVD, Camcorder, Camera, Gaming Device, or VCR Player Connect a HD receiver, DVD, or VCR player to the monitor set and select an appropriate input mode. Back of the product. /DVIDVI INRGB/COMPONENT OUTRGB/COMPONENT INAUDIOINREMOTECONTR...
Эта инструкция также подходит к моделям:Мониторы - 47WV50MS-B (8.58 mb)