Оценок - 0, средний балл: 0
(
)
)
|
Фото и характеристики LG N225WU |
Фрагмент инструкции
The "OSD UNLOCKED" message will be displayed and the screen will be unlocked. SMART+ Use this button to enter AUTO BRIGHT(Only N195WU model), ORIGINAL RATIO menus. AUTO To adjust the monitor settings, press the AUTO button on the MONITOR SETUP OSD menu (only supported for analog signal(D-SUB)). For optimal screen display, use the following resolution. Optimal Resolution N195WU 1366 x 768 N225WU 1920 x 1080 INPUT Allows selection of the input signal. yyIf you connect the monitor to a computer using a D-SUB cable, select either the USB or D-SUB input signal. yyIf only one computer is connected to the monitor, the input signal is detected automatically. The initial input signal is USB. EXIT Exits the OSD menu. (Power Button) D-SUB input yyUse this button to switch the monitor on or off. USB input yyOn : Press the power button to turn on the power. yyMonitor Off : If you press the power button, the monitor will automatically turn off after 5 seconds. yyUSB Off : Press the power button twice to turn off the USB power. Power Indicator N195WU When the monitor is in operating mode, the power indicator will turn purple (on mode). When the monitor is in power saving mode, the power indicator will blink purple. N225WU When the monitor is in operating mode, the power indicator will turn blue (on mode). When the monitor is in power saving mode, the power indicator will blink blue. Lifting and moving the Monitor set When moving or lifting the Monitor set, read the following to prevent the Monitor set from being scratched or damaged and for safe transportation regardless of its type and size. Setting Up the Monitor set Attaching the Stand Base 1 Place the monitor's screen face down. CAUTION yyTo protect the screen from scratches, cover the surface with a soft cloth. CAUTION yyAvoid touching the screen at all times, as this may result in damage to the screen or some of the pixels used to create images. 2 Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure. yyIt is recommended to move the Monitor set in the box or packing material that the Monitor set originally came in. yyBefore moving or lifting the Monitor set, disconnect the power cord and all cables. yyHold the top and bottom of the Monitor set frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area. yyWhen holding the Monitor set, the screen should face away from you to prevent the screen from scratches. yyWhen transporting the Monitor set, do not expose the Monitor set to jolts or excessive vibration. yyWhen transporting the Monitor set, keep the Monitor set upright, never turn the Monitor set on its side, or tilt towards the left or right. Stand Body Stand Base 3 Using a coin, turn the screw clockwise to secure the stand base. Stand Body Stand Base Detaching the stand base 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. Adjusting the stand body 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. 2 Using a coin, turn the screw in the stand base counterclockwise. Detach the stand base from the stand body. 2 Press the button as shown and pull the stand body up. Stand Body Stand Base CAUTION yyThe components appearing in the illustrations may look different from the actual product. yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury. yyTo avoid damaging the screen when lifting or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnecessary pressure on the screen. 15- 5 Mounting on a table 1 Lift the monitor and place it on the table in an upright position. Install at least 10 cm away from the wall to ensure sufficient ventilation. Adjusting the angle 1 Place the monitor mounted on the stand base in an upright position. 2 Adjust the angle of the screen. The angle of the screen can be adjusted up to 15° forwards and 5° backwards for a comfortable viewing experience. 10 cm 10 cm 10 cm 10 cm Front Side Rear Side WARNING yyTo avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor's frame as illustrated below. 2 Connect the adaptor to the monitor, then plug the power cord into the wall outlet. 15- 5 yyBe careful not to touch or press the screen area when adjusting the angle of the monitor. 3 Press the (Power) button on the front of the monitor to turn on the monitor. CAUTION yyUnplug the power cord prior to moving or installing the monitor. There is risk of electric shock. yyWhen you connect the DC jack to the monitor, ensure it is inserted tightly to prevent it from coming loose. Using the Kensington locking device The connector for the Kensington lock is located on the rear of the monitor. For more information on installation and usage, refer to the Kensington lock user manual or visit the website at http...
Эта инструкция также подходит к моделям:Мониторы - N225WU-BN (2.07 mb)