Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
The product may fall and get damaged or injure your foot. 4. Tie down the base lock to perpendicularity direction. 5. Once assembled take the monitor up carefully and face the front side. Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on the surface. cushion or soft cloth. 3. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 4. Pull out the Stand to remove. A4 Connecting the Display 5. Pushing the PUSH button, Take the stand base from stand body. Warning: You can hurt your finger. Good Position Bad Position Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5°~20° Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 A6 Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to . 2. Press button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) 2 Connecting the Display PUSH PC B MAC c PC A Wall-outlet type Power Cord Analog signal D-sub Digital signal DVI A B C Connect DVI Cable Connect Dsub Cable (PC) Connect Dsub Cable (Mac) Mac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) Dsub VGA connector on the supplied cable to a 15 pin 2 row connector. DVI-D(This feature is not available in all countries.) NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product. Control Panel Functions Front Panel Controls Control Function MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 4:3 in Wide To select the image size of the screen. WIDE 4:3 • WIDE : Switch to full screen mode according to input image signal. • 4 : 3 : Change the image signal ratio into 4:3. A7 Control Function Control Panel Functions This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off.Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is -W1942TE : 1440 x 900 Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A15. Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. Control Function Control Panel Functions This Indicator lights up blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber. Use this button to turn the display on or off.Power Button Power Indicator Use this button to enter a selection in the On Screen Display. AUTO/SET Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is -W1942TE : 1440 x 900 Buttons Use these buttons to sel...
Эта инструкция также подходит к моделям:Мониторы - W1942TE-PF (2.28 mb)