4 ASSEMBLING AND PREPARING ENG ENGLISH Parts and buttons Power Indicator yy LED On : Power is on yy LED Off: Power is off (Power Button) Front Side Buttons Input Connectors (...............See p. ........ to ...13.) Detaching the stand base 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. Setting up the Monitor set Attaching the Stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. CAUTION 2 Using a coin, turn the screw in the stand base counterclockwise. Detach the stand base from the stand body. yyTo protect the screen from scratches, cover the surface with a soft cloth. 2 Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure. Stand Body Stand Body Stand Base Stand Base CAUTION 3 Using a coin, turn the screw clockwise to secure the stand base. yyThe components appearing in the illustrations may look different from the actual product. yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury. yyTo avoid damaging the screen when lifting or moving the monitor, only hold the stand or the plastic cover. This avoids putting unnecessary pressure on the screen. yyOnly remove the tape and the locking pin when the monitor is mounted on the stand base and is in an upright position. Otherwise, the stand body may protrude, which may lead to injury. Stand Base Detaching the stand body 1 Place the monitor's screen face down. To protect the screen from scratches, cover the surface with a soft cloth. 2 Using a screwdriver, remove the four screws and detach the stand from the monitor. Using the cable holder Fix the Knob (Cable holder) to the Hole(Hingebody). 1 Use one screw to fix the Cable Holder and monitor set. 2 Close the Cable holder. 3 .............. Mounting on a table 1 Lift the monitor and place it on the table in an upright position. Install at least 10 cm away from the wall to ensure sufficient ventilation. Adjusting the angle 1 Place the monitor mounted on the stand base in an upright position. 2 Adjust the angle of the screen. The angle of the screen can be adjusted up to 5° forwards and 20° backwards for a comfortable viewing experience. 10 cm 10 cm 10 cm 10 cm Front Side Rear Side WARNING 2 Connect the Power cord to the monitor, then plug the power cord into the wall outlet. (Before connect please check the “ON/OFF” knob in “O” state). 1 yyTo avoid injury to the fingers when adjusting the screen, do not hold the lower part of the monitor's frame as illustrated below. 2 Press the “ON/OFF” knob in “ ” state (Open the power). yyBe careful not to touch or press the screen area when adjusting the angle of the monitor. 3 Press the (Power) button on the front of the monitor to turn on the monitor. CAUTION yyUnplug the power cord prior to moving or installing the monitor. There is risk of electric shock. Adjusting the stand height 1 Place the monitor mounted on the stand base in an upright position. Using the Kensington locking device The connector for the Kensington lock is located on the rear of the monitor. For more information on installation and usage, refer to the Kensington lock user manual or visit the website at Connect the monitor to the table with the Kensington lock cable. 2 Remove the tape attached at the bottom rear of the stand body, then pull out the locking pin. Stand Body Tape Locking Pin 3 The height can be adjusted up to 120 mm. 120.0mm NOTE yyUsing the Kensington lock is optional. The accessories can be purchased at your local electronics store. CAUTION yyOnce the pin is removed, it is not necessary to re-insert it to adjust the height. WARNING yyDo not put your finger between the screen and the base (chassis) when adjusting the screen's height. 3 Be careful with the cables when rotating the screen. Swivel stand yyImage shown may differ from your Monitor set. 1 Swivel 355 degrees and adjust the angle of the Monitor set to suit your view. Using the Pivot function The pivot function allows you to rotate the screen 90 degrees clockwise. 1 Lift the monitor to its highest height to utilize the Pivot function. 2 Landscape & Portrait : You can rotate the panel 90° clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. Model 24EB23PY VESA (A x B) 100 x 200 Standard screw M4 Number of screws 8 CAUTION yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur. yyIf you install...

Эта инструкция также подходит к моделям:
Мониторы - 24EB23PY (8.84 mb)