Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Handling the remote control * Do not subject to strong shock. * Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately. * Avoid exposure to heat and steam. * Other than to install the batteries, do not open the remote control. 30° 30° NOTE: The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor, or when there is an obstacle in the radiation path. 11 User Manual BDL4635E How to Mount or Attach Table stand to the LCD Monitor You can install the LCD monitor in one of the following two ways: Method 1: Attach and remove the optional table stand How to install the table stand 1. Please turn the monitor off. 2. After inserting table stand in guide block, fasten the thumbscrews on both sides of the monitor. NOTE: Install the table stand with the longer end of the feet directing to the front. Screws Longer portions directs to the front In the upright position Optional table stand How to remove the table stand 1. Spread the protective sheet on the flat surface. 2. Make the monitor lying on the protective sheet. 3. Remove screws using a screwdriver and place them in a safe place for reuse. 12 User Manual BDL4635E To avoid monitor from falling Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and damage. As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor(BDL4635E: approx. 34.6 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are recommended. Screw Holes Screw hook Rope Clamper Screw * Clamper and Screw here is not supplied. Caution: • Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its effectiveness against any kind of earthquake or disaster. • Before moving the monitor, remove the rope that is securing the monitor. Method II: Mount the monitor on the wall Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit (commercially available). Using mounting interface that comply with TUV-GS and/or UL1678 standard in North America is recommended. Protective Sheet Table Handles 1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the surface as not to scratch the screen face. 2. This device cannot be installed without the correct and complete mounting accessories (not provided in the box). Make sure you have all related parts available for wall mounting. 3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. 4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely. (Recommended torque: 470 - 635N•cm). Caution: For preventing the monitor from falling. • Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of installation, refer to the instructions of the metal brackets. • To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the bracket manufacturer for installation location. • To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this page.) Tabletop stand 13 User Manual BDL4635E Ventilation Requirements for enclosure locating To allow heat to disperse, leave space between surrounding objects as shown in the diagram below. 14 User Manual BDL4635E Setup Procedure 1. Install the system on the right location CAUTION: THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS. Failure to follow this caution may result in injury if the LCD monitor falls. CAUTION: DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY QUALIFIED TECHNICIAN. The LCD display must be installed by a qualified technician. Contact your dealer for more information. CAUTION: DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, FACE UP, OR FACE DOWN. CAUTION: DO NOT INSTALL THE LCD MONITOR AT PLACES WHERE IT WILL BE EXPOSED TO DIRECT SUNLIGHT. Failure to follow this caution will result in display defects. IMPORTANT: Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch t...