Оценок - 3, средний балл: 4.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. • Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color). Important Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. Troubleshooting Display image is incorrect The screen color is mono or abnormal. The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Display image is incorrect The screen color is mono or abnormal. The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? Have you installed the display driver? • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. Or, you can also download the driver from our web site: • Make sure to check if the video card supports Plug&Play function. A21 Specifications W2442PE Display 24 inches (60.9 cm) Flat Panel Active matrix-TFT LCD, Anti- Glare coating Visible diagonal size: 60.9 cm 0.276*0.276 mm pixel pitch Sync Input Horizontal Freq. Analog : 30 - 83 kHz (Automatic) Digital : 30 - 83 kHz (Automatic) Vertical Freq. Analog,Digital: 56 - 75 Hz (Automatic) Input Form Separate TTL, Positive/Negative SOG (Sync On Green), Digital (HDCP) Video Input Signal Input 15 pin D-Sub Connector DVI - D connector (Digital) Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital,HDMI Resolution Max Analog : VESA 1920 x 1080 @60 Hz Digital : VESA 1920 x 1080 @60 Hz Recommend VESA 1920 x 1080 @60 Hz Plug&Play DDC 2B(Digital,HDMI) ,DDC 2AB(Analog) Power On Mode : 42W(Typ.) Consumption Sleep Mode . 1 W Off Mode . 1 W Dimensions With Stand Without Stand & Weight Width 58.22 cm / 22.92 inches 58.22 cm / 22.92 inches Height 43.75 cm / 17.22 inches (Min) 35.40 cm / 13.94 inches 54.75 cm / 21.55 inches (Max) Depth 27.02 cm / 10.64 inches 6.01 cm / 2.37 inches Net 6.2 kg (13.78 lbs) Range Tilt -5°~ 18° Swivel 356° Height 110 mm / 4.33 inches Power Input AC 100-240V~ 50/60Hz 1.2A Environmental Operating Conditions Conditions Temperature 10°C to 35 °C Humidity 10 % to 80 % non-Condensing Storage Conditions Temperature -20°C to 60 °C Humidity 5 % to 90 % non-Condensing Stand Base Attached ( ), Detached ( O ) Power cord Wall-outlet type A22 NOTE Information in this document is subject to change without notice. Specifications Preset Modes (Resolution) RGB/DVI Timing Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 720 x 400 31.468 70 2 640 x 480 31.469 60 3 640 x 480 37.500 75 4 800 x 600 37.879 60 5 800 x 600 46.875 75 6 1024 x 768 48.363 60 7 1024 x 768 60.123 75 8 1152 x 864 67.500 75 9 1280 x 1024 63.981 60 10 1280 x 1024 79.976 75 11 1680 x 1050 65.290 60 *12 1920 x 1080 67.500 60 * Recommend Mode HDMI Timing Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) 1 480P 31.50 60 2 576P 31.25 50 3 720P 37.50 50 4 720P 45.00 60 5 1080i 28.12 50 6 1080i 33.75 60 7 1080P 56.25 50 8 1080P 67.50 60 Indicator LED ColorMODE On Mode Blue Sleep Mode Amber Off Mode Off A23 Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor with its front facing downward on a soft cloth. 2. Separate the stand after firstly separating 4 screws by using a driver as figure. 3. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for ...
Эта инструкция также подходит к моделям:Мониторы - W2442PE-SF (1.28 mb)