Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации LG, модель M2362DP-PZ

Производитель: LG
Размер: 6.94 mb
Название файла:

Язык инструкции:en

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста


К этому устройству также есть другие инструкции:

Фрагмент инструкции


USB Input Euro Scart Socket (AV IN) Connect scart socket input or output from an external device to these jacks. Power Cord Socket This set operates on AC power. The voltage is indicated on the Specifications page. Never attempt to operate the set on DC power. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. This port is used for Service or Hotel mode. COMPONENT INPUT Connect a component video/audio device to these jacks. RGB INPUT (PC) Connect the output from a PC. ANTENNA / CABLE INPUT Connect over-the-air signals to this jack. 8 2 9 3 10 4 11 5 6 PREPARATION P R E PA R AT I O N 6 STAND INSTALLATION ¦ ¦ The image shown may be somewhat different from your set. 1 2 Insert the Stand Base into the product. Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. Stand Base 3 Turn the Stand Base Lock through 90° to fix the Stand Base to the Stand Body. 4 5 Base Lock STAND INSTALLATION ¦ ¦ The image shown may be somewhat different from your set. 1 Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. 2 Insert the stand base into the product. Stand Base 3 Use a Coin on the bottom of the stand base and turn the screw clockwise to tighten. Coin DETACHING STAND ¦ ¦ The image shown may be somewhat different from your set. 2 1 Detach the monitor to the Stand Base by turning the screw to the left. Place the set screen side down on a cushion or soft cloth. 3 Turn the Stand Base Lock through 90° to separate the Stand Base from the Stand Body. 4 Pushing Latch inside, Take the stand base from stand body. Latch DETACHING STAND ¦ ¦ The image shown may be somewhat different from your set. 1 Place the set screen side down on a cushion or soft cloth. 2 Detach the monitor to the Stand Base by turning the screw to the left. Turn the screw by using a Coin. Coin 3 Pull the stand base. DETACHING STAND BODY ¦ ¦ The image shown may be somewhat different from your set. ¦ ¦ Remove the Stand Body in the same way as the following when using it as a Wall Hook. 1. Remove the screw 2 point. 2. Pull the stand body. 1. Remove the screw 4 point. 2. Pull the stand body. WALL MOUNT : HORIZONTAL INSTALLATION For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 10 cm 10 cm 10 cm 10 cm 10 cm If you intend to mount the set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the set using the wall mounting interface (optional parts), attach it carefully so it will not drop. 1. Be sure to use screws and a wall mount that meet VESA standards. 2. Using screws longer than those recommended might damage the product. 3. Using screws that do not meet VESA standards might either damage the product or result in it coming away from the wall. We will not be held responsible for any damage resulting from failure to follow these instructions. 4. VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications 5. Please use VESA standard as below. 5-1) 784.8 mm (30.9 inch) and under * Wall Mount Pad Thickness : 2.6 mm * Screw : . 4.0 mm x Pitch 0.7 mm x Length 10 mm 5-2) 787.4 mm (31.0 inch) and above * Please use VESA standard wall mount pad and screws. Wall Mount Pad < Screw Mounting Interface Dimension > . M1962DP/M2062DP/M2262DP/M2362DP : 100 mm x 100 mm hole spacing . M2762DP : 200 mm x 100 mm hole spacing DESKTOP PEDESTAL INSTALLATION ¦ ¦ The image shown may be somewhat different from your set. For proper ventilation, allow a clearance of 10 cm on each side and from the wall. 10 cm 10 cm 10 cm 10 cm POSITIONING YOUR DISPLAY ¦ ¦ The image shown may be somewhat different from your set. Adjust the position of the panel in various ways for maximum comfort. * Tilt range -5° 15° SWIVEL STAND(Only M2762DP) ¦ ¦ The image shown may be somewhat different from your set. After installing the set, you can adjust the set manually to the left or right direction by 179 degrees to suit your viewing position. LOCATION Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also, ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. WARNING ¦ ¦ When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). SECURING THE SET TO THE WALL TO PREVENT FALLING WHEN THE SET IS USED ON A STAND (Only M2762DP) ¦ ¦ The image shown may be somewhat different from yo...

Эта инструкция также подходит к моделям:
Мониторы - M2062DP-PR (6.94 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории