A7 . Refer to the next page for Auto Mirror function. Tilt the screen while rotating it so that the monitor does not touch the floor. Do not hold the screen area as shown in the picture when rotating it, otherwise your fingers might get hurt or get stuck. Using the Auto Pivot and Auto Mirror functions degrees> Tilt the screen while rotating it so that the monitor does not touch the floor. Do not hold the screen area as shown in the picture when rotating it, otherwise your fingers might get hurt or get stuck. Auto Mirror Screen switch : The monitor screen is automatically reversed when you switch it forward/backward as shown in the figure. . Caution : Do not touch the screen while you rotate the panel. . This rear view represents a typical model. Your display model may differ from the illustration below. A8 Tip If you activate the Auto Pivot or the Auto Mirror function while the screen is almost level, the screen may not work properly. In this case, set the screen upright and adjust it to the proper angle. It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. Control Panel Functions Front Panel Controls Bottom A9 MENU Button Use this button to enter or exit from the On Screen Display. Control Function OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears. -+ Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A16. Use this button to make either D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. + Button (SOURCE Hot key) -Button ( ) Control Panel Functions AUTO/SET Button Control Use this button to selection an icon in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button prior to entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1280 x 1024 Function Power Button Use this button to turn the display on or off. Power Indicator This Indicator lights up as blue when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color will changes to amber. AUTO BRIGHT Sensor You can make the screen brighter or darker by covering the AUTO BRIGHT Sensor. To use the AUTO BRIGHT function, go to OSD menu in Setup menu and turn on AUTO BRIGHT. Default setting is OFF. A10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the display's image size, position and operating parameters is quick and easy with the On Screen Display Control system(OSD). A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make by using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making any image adjustments. To make adjustments in the On Screen Display, follow these steps: AUTO/SET MENU MENU-+ -+ Press the MENU button, then the main menu of the OSD appears. To select each item in the OSD menu, use the -or + button. When the icon you want is highlighted, press the AUTO/SET Button. Use the -/ + buttons to adjust the image to the desired level. Use the AUTO/SET button to select other sub-menu items. Press the MENU button once to return to the main menu to select another function. Press the MENU button twice to exit from the OSD. A11 On Screen Display (OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. PICTURE Main menu Sub-menu BRIGHTNESS A D To adjust the brightness, contrast and gamma of the screen Reference CONTRAST GAMMA COLOR PRESET sRGB To customize the color of the screen6500K 9300K RED GREEN BLUE POSITION HORIZONTAL To adjust the position of the screenVERTICAL TRACKING CLOCK To improve the clarity and stability, sharpness of the screen PHASE SHARPNESS SETUP LANGUAGE To customize the screen status for a user's operating environment WHITE BALANCE AUTO BRIGHT FACTORY RESET POWER INDICATOR OSD POSITION HORIZONTAL VERTICAL FLATRON F-ENGINE MOVIE / TEXT To select or customize desired image settingsUSER NORMAL : Adjustable A : Analog Input D : Digital Input A12 NOTE The order of icons may differ depending on the mo...
Эта инструкция также подходит к моделям: Мониторы - L1982U (1.28 mb)
)
Войти: