Оценок - 2, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
3. Pull the stand base down at the same spot shown in the picture, and the stand will be unfolded. A3 4. Place the monitor upright and adjust the stand base to the desired angle. Adjust the stand base's angle by holding the edges of the monitor gently with both hands. Important This illustration depicts the typical connection procedure. Your monitor may differ from the one displayed in the pictures above. Do not touch or apply force to the monitor's screen while expanding or folding the stand base. Connecting the Display Folding the stand base 1. Face the front of the monitor dislpay. Than gently push the monitor backwards, following the sequence shown in the picture below. Tilt range 1. Make sure that the angle of the panel is set for your comfort. Tilt Range : 0.~30 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees A4 Connecting the Display To adjust the height Scope of adjusting the height : maximum 4.02 inches (102 mm) 102 mm A5 Connecting the Display Using the Computer 2 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form to . Wall-outlet type MAC Power Cord 12 Mac adapter NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. PC 1 PC Varies according to model. Signal Cable A B C Connect DVI Cable Connect Dsub Cable (PC) Connect Dsub Cable (Mac) DVI-D(This feature is not available in all countries.) For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. 2. Press button on the side switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution. A6 Connecting the Display To arrange the cables 1. Insert and screw the cable holder into the hole in the back of the stand until it will not turn any more as shown in the following figure. 2. After connecting the cables neatly, arrange the cables to the Cable Holder as shown in the following figure. A7 Cable Holder Control Panel Functions Front Panel Controls 6 Bottom Control Function ZOOMING At the current display, Use 'ez Zooming' Key, then the display resolution is transferred to the one step low resolution. Use 'ez Zooming' Key one more, the display is back to the original display. Those with poor eyesight such as the elderly, those who have difficulty using computers and children can enlarge text or pictures by adjusting resolution with a single touch. To use this feature, please install forteManager program in the enclosed CD-ROM. The resolutions at which the EZ ZOOMING operates are as follows: 1280 x 1024, 1024 x 768, 800 x 600. The setting method can differ by O/S or video card. In this case, Please ask to the computer or the video card manufacturer. MENU Button Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears. A8 Control Panel Functions This Indicator lights up as blue when the display is operating normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color will changes to amber. Use this button to turn the display on or off.Power Button Power Indicator Use this button to selection an icon in the On Screen Display. AUTO/SET Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button prior to entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1280 x 1024 Control Function -+ Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A15. Use this button to make either D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. + Button (SOURCE Hot key) -Button ( ) A9 On Screen Display (OSD) Control Adjustment Screen ...
Эта инструкция также подходит к моделям:Мониторы - L1972H (1.08 mb)