• Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents. • Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. • To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10 cm away from the wall surface. • Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. • Please use Wall Mount according to the International standards. 21 Using the Software Using the WebCam Monitor This monitor can be used as a normal monitor for video communications and for viewing multimedia files simply by connecting the power cable and the USB cable to your PC. Minimum baseline spec • System Requirements CPU : 1.73GHz or Later OS : Windows XP Service Pack2 or later. However, Windows Vista 64bit is not supported. RAM : 512 MB RAM or more USB : 1.1 or higher (USB 2.0 recommended) Auto Setup for the web camera, microphone and speaker 1. Connect your monitor and PC using a USB cable, as shown in the figure below. 22 Using the Software 2. The web camera, microphone and speaker will be set up automatically and appear on the status bar. Note • If the camera is recognized as a USB1.1 device, the screen quality may be degraded and noise may occur. Make sure to upgrade to USB 2.0. • Because of the characteristics of USB communication, the device is recognized whenever it is turned off and on. When the recognition process is finished, you can use it normally. • If you remove the cable while your PC is recognizing a USB device, it may cause a serious error to your PC. • Do not turn the camera too forcefully. This may cause a product malfunction • Make sure to remove the USB cable after clicking on the icon on the taskbar of your PC and unloading the USB device from Windows. Installation Precautions 1. Never disconnect the USB cable from the USB port while the auto installation is in progress. (The installation takes about a minute. If you remove the USB port during the installation, a severe problem may occur with your PC.) 2. Do not turn off the monitor while the auto installation is in progress. (If you turn off the monitor during the installation, a severe problem may occur with your PC.) 3. The screen may blink when the auto installation is completed. (This occurs when your PC recognizes your monitor as a USB device. This is not a fault.) 4. If the auto installation is completed, configure the position and resolution for the monitors in the [Settings] tab of the [Display Properties] window. (The optimal resolution for this monitor is 1680 x 1050.) 5. If you change the USB Port after your PC has recognized a USB device, it may cause a USB device recognition error. (You must remove and reinstall the driver.) 23 Using the Software If the installation fails Note If the installation is stopped because the New Hardware Wizard has failed, right-click ”My computer“, and click “Properties” - “System Properties” - the ”Hardware“ tab. Click on the ”Device Manager“ and reinstall the driver by following these steps below. 1. The symbol showing that the device has failed to be installed is displayed as shown in ( , ) 2. In this case, click ”Scan for hardware changes” to run the Setup Wizard again. At this time, if the installation fails, click ( , ) and right-click it. Select ”Driver Update” from the displayed menu. Checking the configuration Note After the installation, you can check the configuration by following these steps: 1. Right-click My computer, click Properties - System Properties - Hardware tab. 24 Using the Software 2. Click on “Device Manager”. 3. A list of installed devices will be displayed, as shown in the figure below. Checking the Web Camera Setup 1. Double-click My Computer on the Windows Desktop. 2. Double-click the USB Video Device #2. You should find that the web camera has been set up normally, as shown in the figure below. Checking the Microphone and Speaker Setup 1. Double-click Sounds and Audio Devices in the Control Panel. 25 Using the Software 2. Select the Voice tab and click on Test Hardware. Note If the sound from your monitor is too soft, adjust the volume after setting the volume of your PC to the maximum. 3. Follow the steps described below. You should find that the microphone and speaker have been set up. Restrictions on Using the Monitor 1. The Camera and Audio functions of this monitor except the basic Display function are recognized as USB Devices. 26 Using the Software Note This monitor must be connected with a D-Sub (Analog) or a DVI-D cable (Digital) when used as a normal monitor...
Эта инструкция также подходит к моделям: Мониторы - 2263UW (4.99 mb)
)
