Оценок - 4, средний балл: 3.8
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
To enable audio when DVI Device is selected, be sure to establish the connection using step ( ). Connect the Audio cable for your LCD Display to the Audio port on the back of the LCD Display. Connect the power cord for your LCD Display to the Power port on the back of the LCD Display. Turn on the power switch. Note Contact a local SAMSUNG Electronics Service Center to buy optional items. Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and the input port on another monitor using a DVI cable. Connect between the [AUDIO OUT] port on the LCD Display and the audio input port on another monitor using a stereo cable. Note • Select DVI Mode as an input source for the external monitor connected to [DVI OUT]. • DVI OUT does not support HDCP. Connecting AV Devices Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . 2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . 3. Press SOURCE on the product or remote control and select "AV". 4. Then, start the Camcorders with a tape inserted. Note The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables. Blue Customize the intensity of blue color for the selected display device. System Setup Tool Settings Other Functions Note You do not need to select a language if you will be using English as the menu display language. PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPM compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature. PowerSaver State Normal Op- Power sav- Power off Power off eration ing mode (Power Swich) Power Indicator On Blinking Amber Off 400UXN-3 250 Watts 5 Watts 5 Watts 0 Watts (852.5 BTU/ (17.05 BTU/ (17.05 BTU/ (0 BTU/h) h) h) h) 400UX-3 200 Watts 2 Watts 1 Watts 0 Watts Power Con- (682 BTU/h) (6.82 BTU/h) (3.41 BTU/h) (0 BTU/h) sumption 460UXN-3 300 Watts 5 Watts 5 Watts 0 Watts (Typical) (1023 BTU/ (17.05 BTU/ (17.05 BTU/ (0 BTU/h) h) h) h) 460UX-3 230 Watts 2 Watts 1 Watts 0 Watts (784.3 BTU/ (6.82 BTU/h) (3.41 BTU/h) (0 BTU/h) h) Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follo...
Эта инструкция также подходит к моделям:Мониторы - 400UX-3 (4.54 mb)
Мониторы - 460UX-3 (4.54 mb)
Мониторы - 460UXN-3 (4.54 mb)