Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
The AC Power cord must be used with a properly grounded and polarized power supply socket. The AC Power cord supplied is for the USA (UL) and Canada (CSA) for use with the display unit. For use in other countries, make sure the AC Power cord meets the safety standards of the country. • Place the AC Power cord where it will not be subject to stress. • Use only Panasonic provided accessories or the exact equivalent. 2) Usage • Pulling on the AC Power cord or VGA Signal Cable can damage the display unit (monitor) and can cause the unit to fall and possibly cause personal injury. • Receiving trouble. If there is a television set or other display unit nearby, keep your display unit as far away from it as possible. Mutual interference can cause image distortion or noise. • Long exposure to rubber or vinyl products can stain the cabinet. • Keep the monitor from physical shock when moving. Be careful of the Cathode Ray Tube (CRT). • Do not place anything on the monitor. • Also take good care of the AC Power cord: Do not place any objects on the AC Power cord. Do not attempt to extend, shorten or tie it into a knot. 3) Product Care • Prior to cleaning your display unit, disconnect the AC Power cord and the VGA Signal Cable or BNC Cable from the display unit. • Use a clean, soft, dry cloth to clean the outside of the monitor or the CRT surface. If the monitor or CRT surface is very dirty, wet a clean, soft cloth with neutral detergent (such as dishwashing detergent) and water, squeeze it tight until almost dry, wipe the monitor or CRT surface with it, and finish by wiping with a clean dry cloth. Do not use any solvents. • Do not rub or strike the monitor with anything hard or harsh as this may scratch, mar or damage the monitor permanently. • Do not use a chemical duster or polish-cleaner because it can adversely affect the unit and peel the paint coat. 4 Features 1) High Image Quality in a Package • Panasonic Panasync/Pro P110 i with a CRT 21' (20.0" / 50.8 cm Viewable Image Size) has image quality that has to be seen to be believed. It has a 0.25 mm ultra fine dot pitch and up to 1,600 x 1,200 at 92 Hz / 1,800 x 1,440 at 70 Hz maximum resolution. The Panasync/Pro P110 i produces sharp saturated color images with High Contrast and Brightness that can be viewed over a wide viewing angle. • Combined with optimized dynamic focusing circuitry, the CRT has improved beam landing accuracy, focus, convergence and lower raster distortion than a typical 21-inch CRT. This gives the Panasync/Pro P110i a sharper, more uniform focus, especially in the corners of the screen, traditionally a focus problem area. Crystal Pigment Phosphors and Advanced Invar Mask provide increased Contrast and Brightness. • Panasync/Pro digital multi-scan 30 kHz to 117 kHz* Horizontal and 50 Hz to 180 Hz Vertical scanning frequencies can be automatically scanned. Eight timing selections have been preset at the factory and 20 user programmable selections are provided. 2) Crystal Pigment Phosphors • Crystal Pigment Phosphors provide increased brightness and contrast for the P110 i creating crisp colorful images. Each grain of Crystal Pigment Phosphor is covered with a filter material of the same color to filter external light. 3) Advanced INVAR Shadow Mask and Dark tint • The CRT also features an Advanced INVAR Shadow Mask, which is manufactured with an improved material and designed to be positioned closer to the screen glass. When combined with the Dark tint of the screen, this results in a 10% overall increase in brightness, improved purity due to less environmental movement, and better overall color uniformity. 4) New DQ-DAF™ Electron Gun with Super New OLF • The new DQ-DAF (Double-Quadruple Dynamic Astigmatism and Focus) electron gun reduces the degradation of the screen focus, realizing higher resolution. In addition, the super new OLF (Overlapping Field) main lens for the P110i creates a smaller spot size which contributes to sharper images. 5) Digital adjustment using on-screen Menu (OSM) • The On-Screen Menu is available in five (5) languages. English, French, German, Italian or Spanish can be selected. Custom adjustments can be made quickly and easily through the On-Screen Menu utilizing four buttons on the front panel. The On-Screen Menu may be positioned in one of six locations and color in one of six colors on the Display Screen. A Self-Test On-Screen display is provided with no signal input or an Error On-Screen Menu if the Horizontal or Vertical Scanning frequencies are outside the specified range. 6) The P110 i is Plug & Play • VESA* DDC™ 1 / 2B compatible (Video Electronics Standards Association Display Data Channel). This allows the PI 10i to inform a compatible host of its capabilities that meet the Microsoft* / Intel® Plug & Play Definition used by Windows* 95 and Windows® 98. 7) Self-test menu • The display unit can be checked via the self-test menu displayed on the screen. This menu can be accesse...