Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
1. Using a small screwdriver, pry open the transparent battery cover. Coin battery Put the battery into the space provided Push gently in to snap closed Replacing the battery in the remote control 2. Replace the battery with the same type (Model CR2025) and snap the cover closed. Changing the dome lights 1. Using a small straight-edged screwdriver, gently pry the cover away from the light fixture. Opening the light cover 2. Using the same small straight-edged screwdriver, gently remove the light bulb. 12 OHM106/156 OHM.pmd 12 2006-02-28, 13:00 Removing the bulb 3. Replace the bulb with the same type bulb. 5. INSTALLATION AND WIRING Read these instructions and precautions carefully. Improper installation can damage the monitor and the vehicle. What is included in the box In addition to this manual, the box contains: • 1 OHM106 or OHM156 • 1 remote control • 1 audio/video RCA accessory • 1 four-pin power harness • 1 metal mounting bracket • 2 mounting keys • 2 plastic covers to cover the key holes • 4 screws and plastic covers for attaching the unit to the ceiling bracket • 1 soft, black rubber gasket (usually attached to the unit) • 1 EMC cover (wiring harness cover) • 3 screws for the EMC cover • 1 FM modulator control cable (FM MOD only; FM200 not included) • 1 dual-channel set of head phones (WH204H) OHM106/156 13 English OHM.pmd 13 2006-02-28, 13:00 English Tools and additional components You will need: • A Phillips-head screwdriver when mounting the unit in the vehicle • 4-6 screws to attach the ceiling bracket to the ceiling of the vehicle (not included) • High-quality RCA input-output cables Extra cable can cause signal loss and act as an antenna for noise. Use only high- quality RCA cables that are no longer than necessary to make a direct connection with the source unit(s) and monitor. Before you begin 1. Verify that the vehicle electrical components function, including: power windows, power door locks, air conditioning, lights, etc. 2. Test fit the location of the overhead monitor system to ensure it will not interfere with the operation of the vehicle. 3. If applicable, verify that the monitor, when mounted, will not interfere with the operation of the sun roof. 4. Determine the location of the audio/video source(s). 5. Disconnect the negative battery terminal before making any wiring connections. CAUTION Do not open the case.There are no serviceable parts inside. If you drop anything into the unit during installation, consult with your Clarion Dealer or an authorized Clarion service center. Mounting and wiring precautions The OHM106/156 should be mounted in the ceiling of the vehicle. The front panel controls should be easily accessible from the rear seat. In addition: • This unit is exclusively for vehicles with a negative ground, 12V power supply. • This unit requires additional mobile audio components, such as a DVD player, for proper operation. • Always use great care when attaching anything to a vehicle! Check clearances on both sides of the planned installation before drilling any holes or installing any screws. 14 OHM106/156 OHM.pmd 14 2006-02-28, 13:00 • A good chassis ground connection is critical to minimize resistance and avoid noise problems. Use the shortest wire possible and securely connect it to the car chassis and the source unit ground. • When routing RCA cables, keep them away from the power cables and output speaker wires, engine, exhaust system, etc. Heat may damage wires. • If the fuse should blow, make sure all connections are correct and no wires are damaged before replacing the fuse. Always use fuses that are the same amperage value as the original fuse. When replacing a fuse, never let the battery side touch any metal part or any other wire. W ARNING! To prevent short circuits during installation, disconnect the vehicle’s negative (-) battery lead before making any power connections. Installation procedure The OHM106/156 replaces the car’s dome light. This section provides basic tips and techniques to aid the installation. These are not vehicle specific, but should be used as guidelines for performing the installation. Preparation 1. Identify the polarity of the dome light circuit and set the switch on the bottom of the overhead monitor housing. 2. Test fit the overhead monitor system on the ceiling of the vehicle. Verify that it will not interfere with the save operation of the vehicle. 3. Carefully mark the location with masking tape. 4. Lower the vehicle’s headliner down to see if a roof support beam is available to screw the mounting bracket to. If a support beam is not available, use a 3/4 inch piece of plywood cut to the appropriate size. Attach the plywood to the roof of the vehicle using silicone. Allow for adequate drying time. 5. Double-check the length of the mounting screws (not included) to make sure they will hold the unit securely. OHM106/156 15 English OHM.pmd 15 2006-02-28, 13:00 Install the monitor 1. Carefully hold the overhead monitor up to the ceilin...
Эта инструкция также подходит к моделям:Мониторы - OHM106 (831.56 kb)