Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Consult the earlier section More Psion and file handling notes first if you are not adequately familiar with the Psion's routines. On the Workabout: ¦ Exit from the SunData application (if necessary) by pressing . ....+X. ¦ In the System Screen, press Menu, Spec, Remote Link, and press Enter. Set the Remote link to On, Baud rate to 9600, and the Port to A. Press Enter to accept. ¦ Connect the RS232 port at the top right of the Workabout to the PC’s COM1 serial port with the SunScan comms cable. On your PC: ¦ Exit Windows. From the DOS prompt, in the directory holding SLINK.EXE, type: SLINK . .... You will get an SLINK acknowledgement like this (or similar): Psion MC/HC/Series3 File Server Version 1.2 -Copyright (C) Psion Plc 1991 Press Q to Quit As an example, let us consider how to transfer a new version of the SunData program to the Workabout from your PC. We will assume you have already copied the program file SunData.app into a directory called C:\SUNSCAN\PSION on your Hard Disk. The same process can be used if you need to re-load the SunData program for any reason. SunData.app needs to run from a subdirectory \SUN\ on the Internal drive. You must create this, if it is not already present. On the Workabout: 78 • •••• Appendices Document code: SS1-UM-1.05 ¦ From the Psion System Screen, press Menu, Disk, Directory, Enter. ¦ Press < <<<<> >>>> to select the Disk Internal, (or any other Disks or drives). Note: the Workabout refers to its own drives as Internal and Disk A, B, C etc . The drives on the PC are referred to as REM::A:, REM::C: (REM = remote). If no subdirectory \SUN\ exists, then create one as follows: ¦ Select \, the root directory of the Disk Internal ¦ Press Menu, Directory, Make directory, Enter. ¦ For Dir. Name type \SUN and press Enter. ¦ Access the directories again with Menu, Disk, Directory, Enter. The new subdirectory \SUN\ will now be listed under the root directory of the Internal Disk. ¦ Now press < <<<<> >>>> to move to the REM::C: drive (your PC's hard disk) and enter the \SUNSCAN\PSION directory. ¦ Press ^ ^^^^ or v vvvv to highlight the file Sundata.app. Don't press Enter! ¦ Press Menu, File, Copy file, Enter. ¦ Complete the dialog box as shown below, noting the general advice. If you leave the filename blank after the backslash, the original filename will be used. If you want to change the filename, type in the new filename, with its extension, after the directory path. You must specify the full subdirectory path of the Disk. Start and finish with backslashes(\). ¦ Press Enter to accept, when you are happy with all the details. The Workabout will warn you if you have chosen a filename that already exists, and offer you various options. Otherwise it will proceed, and briefly advise you of the copying process. A copy of the file is now in the new location you have specified. You must also copy across the file Sys$8087.ldd to the same directory on the Workabout, for the SunData program to run properly. You can do this by a similar procedure. Finally: ¦ On your PC, quit the SLINK program by typing Q. ¦ On the Workabout, close down the Remote Link: From the System Screen, press Menu, Spec, Remote Link, and set it to Off, then press Enter. If the SunData icon does not automatically appear in the Psion System screen, see More Psion and file handling notes about re-installing SunData as an application. SunScan User Manual v 1.05 Appendices • •••• 79 Example using RCOM On the Workabout: ¦ Exit from the SunData application on the Workabout by pressing . ....+X. ¦ In the System Screen, press Menu, Spec, Remote Link, and press Enter. Set the Remote Link to On, Baud rate to 19200, and the Port to A. ¦ Connect the RS232 port at the top right of the Workabout to the PC’s COM1 serial port using the SunScan comms cable. From the PC ¦ At the DOS prompt, in the directory holding RCOM.EXE, type: RCOM. .... (Let's assume this is in your C:\SUNSCAN\COMMS directory) The RCOM prompt "»" followed by the current subdirectory name will appear, in a DOS-like screen. You should now be able to get a directory listing of the Workabout Internal Disk on your PC by typing DIR I: . .... at the prompt. Note: in RCOM, the Workabout drives A, B and Internal are mapped onto drives L, R and I. ¦ If the subdirectory \SUN\ does not exist you must create it as follows: >>C:\SUNSCAN\COMMS>I:. .... >> I:\>md\sun. .... ¦ Check the new subdirectory now exists: >> I:\>dir. .... ¦ Then type >> I:\>copy c:\sunscan\psion\*.* I:\sun\. .... This copies both the SunData program sundata.app and sys$8087.ldd, which is also required, to the Workabout Internal drive subdirectory \SUN\ and confirms the process. When you have finished: ¦ On your PC, type EXIT. .... to exit from RCOM ¦ On the Workabout, close down the Remote Link: From the System Screen, press Menu, Spec, Remote Link, and set it to Off, then press Enter. If the SunData icon does not automatically appear in the Psion System screen, see More Psion and file handling notes ...
Эта инструкция также подходит к моделям:Мониторы - SS1-UM-1.05 (658.08 kb)
Мониторы - SS1-UM-1.05 (658.08 kb)
Мониторы - SS1-UM-1.05 (658.08 kb)
Мониторы - SS1-UM-1.05 (658.08 kb)