Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Failure to observe these precautions could result in fire, bodily injury, and damage to the equipment. ¦ Do not operate controls, make adjustments, or perform procedures to a laser device other than those specified herein or in the CD-ROM drive installation guide. ¦ Allow only Compaq-authorized service technicians to repair the laser equipment. ¦ All Compaq systems equipped with CD-ROM drives comply with appropriate safety standard including IEC 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product. It does not emit hazardous light; the beam is totally enclosed during all modes of customer operation and maintenance. This system is classified as a CLASS 1 LASER PRODUCT. This label is located on the outside of your system. A similar label also appears on the internal CD-ROM installed in your system. User’s Guide Packing and Unpacking A A WARNING: Compaq recommends that two people take the monitor from or place the monitor into the box. This helps ensure that the monitor is not dropped. Dropping the monitor may result in personal injury or injury to the equipment. Care and Maintenance To enhance the performance and extend the life of your monitor, use the following guidelines: ¦ Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating properly, or has been dropped or damaged, first unplug your monitor from the power outlet, then contact your Compaq authorized dealer, reseller, or service provider. ¦ Adjust only those controls that are discussed in the operating instructions. ¦ Place your monitor at least 3 inches (76 mm) away from walls or other enclosures. ¦ Use only a power source and connection appropriate for this monitor, as indicated on the label/back plate of the monitor. ¦ Be sure the total ampere rating of the products connected to the outlet does not exceed the current rating of the electrical outlet, and the total ampere rating of the products connected to the cord does not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A) for each device. ¦ Install your monitor near an outlet that you can easily reach. Disconnect the monitor by grasping the plug firmly and pulling it from the outlet. Never disconnect the monitor by pulling the cord. ¦ Turn your monitor off when not in use. You can substantially increase the life of your monitor by using a screen saver program. User’s Guide ¦ Unplug your monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. If the screen requires additional cleaning, use an antistatic CRT screen cleaner. A A CAUTION: Do not use benzene, thinner, ammonia, or any other volatile substances to clean your monitor or the screen. These chemicals may damage the cabinet finish as well as the screen. ¦ Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. ¦ Do not place plants on top of your monitor. Water or dirt from the plant may get into the vents. ¦ Do not drop your monitor or place it on an unstable surface. ¦ Do not allow anything to rest on the power cord. Do not walk on the cord. ¦ Keep your monitor in a well-ventilated area, away from excessive light, heat or moisture. Keep your monitor away from high-capacity transformers, electric motors, and other devices with strong magnetic fields. ¦ In a two-monitor system, place your monitors as far apart from one another as possible to lessen interference between them. ¦ Do not place the monitor face down. Damage could result to the front panel controls or the monitor screen. A A CAUTION: Burn-in image damage may occur on monitors that display the same static image on screen for a prolonged period of time. To avoid burn-in image damage on your monitor screen, you should always activate a screen saver application or turn off the machine when it is not in use for a prolonged period of time. User’s Guide Attach Base to Monitor On some monitors, the base must be attached prior to monitor installation. If you need to attach the base, follow these steps: 1. Align the hooks on the base with the sockets on the bottom of the monitor and attach the base. 2. Push the base toward the front of the monitor until it stops. User’s Guide Install Monitor Before installing your monitor, place it in a convenient, well-ventilated location near your computer. 1. Turn off the power to your computer and other peripheral devices. 2. Connect the video cable (blue connector) 1 from the back of the monitor to the blue 15-pin connector on the back of the computer. Tighten the cable screws to secure the cable to the connector. A A CAUTION: To avoid damaging the video cable, ensure that the cable aligns with the 15-pin connector. Do not force the cable onto the connector. 3. C...