Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
. CAUTION Risk of Fire – Do not add fuel when the product is operating. • Do not operate if fuel has been spilled. Instead, move the machine to a different location and avoid creating sparks. • Do not remove the gas tank cap or add fuel while the engine is running or hot. Add fuel after the engine has cooled by waiting 2 or more minutes after the engine is stopped. • Do not smoke when adding fuel • Do not allow the high pressure hose to come into contact with the muffler guard. • Do not leave the machine running unattended. • Avoid tipping the machine on its side. • Do not operate the machine with the muffler or the air cleaner removed. Especially for the muffler, check the tightness of mounting screw, damage and leakage periodically, and if abnormality is found, repair or replace it. • Occasionally inspect the fuel system componets to check for cracks and leaks. Replace components when necessary. 4 English . WARNING • Do not check for spark with the spark plug removed. • Do not touch the high-voltage cord or spark plug cap. • Do not stop the machine by using the choke lever. • Do not unreasonably adjust the engine speed. • Do not place hands or feet near moving or rotating parts. • Do not operate machine with combustible material in the muffler area. . CAUTION • Do not touch hot surfaces or allow accessories to contact hot surfaces. • The machine has hot surfaces which can cause burns. Operate the unit in a safe environment and away from children. • Remove trash, grass and other debris from around the cooling fins and recoil starter. • Allways use new gasoline. Old gasoline could cause build up in the carburetor which could cause poor engine operation. SAVE THESE INSTRUCTIONS WATER SUPPLY (Cold Water Only) . CAUTION When connecting the water inlet to the water supply mains, local regulations of your water company must be observed. In some areas the unit must not be connected directly to the public drinking water supply. This is to ensure that there is no feedback of chemicals into the water supply. Direct connection via a receiver tank or backflow preventer, for example, is permitted. Dirt in the feed water will damage the unit. To avoid this risk, we recommend fitting a water filter. • Garden hose must be at least 5/8 inch in diameter. • Flow rate of water supply must not fall below 2.8 GPM (gallons per minute). • Flow rate can be determined by running the water for one minute into an empty 5-gallon container. • The water supply temperature must not exceed 104°F/40°C. • Never use the pressure washer to draw in water contaminated with solvents, e.g. paint thinners, gasoline, oil, etc. • Always prevent debris from being drawn into the unit by using a clean water source. Use additional water filter. • Do not operate pressure washer without the water turned on. English 5 6 English .. STEP 1: Attach the handle to the frame of the pressure washer. Align holes, insert bolts, and tighten with knobs. .. STEP 2: Mount the gun/hose storage hanger. .. STEP 3: Attach the high pressure hose to the spray gun. .. STEP 4: Attach the wand to the spray gun. Please follow the instructions step-by-step. Failure to follow the instructions explicitly could lead to premature failure of the engine. CAUTION Engine shipped without oil. Before starting engine, fill with oil. Do not over-fill. Do not run the engine with a high or low oil level as this can cause engine damage. .. STEP 1: Add the oil (1 bottle of SAE 15W 40SF/ SJ) supplied wiht your pressure washer to the engine crankcase only. Failure to add engine oil will cause engine failure. This type of failure is not covered by the manufacturer’s warranty. Oil amount should not exceed 10 oz / 300ml. Below indicates the optimal levels when adding or checking oil. ASSEMBLY INSTRUCTIONS OPERATING INSTRUCTIONS . CAUTION Too much oil can cause the engine to overheat. Signs include but are not limited to the following: a decrease in engine performance, oil leaking from the governor arm, an oil seal, or the air filter. To correct this, immediately drain the oil from the engine and make sure you are using the correct amount of oil as shown previously. • STEP 2: Before starting the engine, move the CHOKE lever to the CHOKE position as indicated. After engine has warmed and idles smoothly, move CHOKE lever to the RUN position as indicated. Warm engine starting: Move the CHOKE lever to the CHOKE position as indicated in the previous step. Once you have achieved stable idle, move CHOKE lever back to RUN position. • STEP 3: Connect the high pressure hose to the unit’s high pressure outlet. • STEP 4: Connect garden hose to unit’s water inlet. • STEP 5: Connect garden hose to the cold water source and turn water on completely. Do not use hot water. • STEP 6: If the trigger gun safety lock is engaged, please disengage. Hold the trigger gun open until all trapped air is eliminated from the low pressure water stream. • STEP 7: Check oil level. Please see STEP1 for details on min/ max levels • ST...