Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
OPERATION MAINTENANCE .WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. .WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. .WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to stop, and disconnect spark plug wire and move it away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. .WARNING: Do not at any time let brake fluids, gasoline, petroleum- based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts should be replaced at an authorized service center. Before running the engine, perform the following pre- operation steps: n Check that all bolts, nuts, etc., are securely tightened. n .Make sure the air filter is clean. n .Check both the engine oil level and the fuel tank level; refill as needed. n .Inspect the work area for hazards. n .If there is excessive noise or vibration, stop the unit immediately. NOZZLE MAINTENANCE Excessive pump pressure (a pulsing sensation felt while squeezing the trigger) may be the result of a clogged or dirty nozzle. n .Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure. n .Remove the nozzle from the spray wand. NOTE: Never point the spray wand at your face. n .Using a straightened paper clip or nozzle cleaning tool (not provided), free any foreign materials clogging or restricting the nozzle. n .Using a garden hose, flush debris out of nozzle by back flushing (running the water through the nozzle backwards or from the outside to the inside). n .Reconnect the nozzle to the spray wand. n .Turn on the water supply and start the engine. LONG-TERM STORAGE OF THE PRESSURE WASHER See Figure 17. .....Store the pressure washer with the gas tank empty by either draining the tank or running the pressure washer until the gas runs out. Allow 30 minutes of “cool down” time before storing the machine. Store in a dry, covered area where the weather can’t damage it. It is important to store this product in a frost-free area. Always empty water from all hoses and the pump. NOTE: Use of a fuel stabilizer and pump saver will give you better performance and increase the life of the machine. Discharge Fuel: Drain the fuel tank completely. Stored gas can go stale in 30 days. Engine Oil: Drain the oil and replace with fresh, clean oil. Spark Plug: n Disconnect spark plug wire and remove the spark plug. Pour about a teaspoon of clean, air-cooled, four-cycle oil through the spark plug hole into the combustion chamber. n Leaving the spark plug out, pull the starter cord two or three times to coat the inside of the cylinder wall. n Inspect the spark plug and clean or replace, as necessary. n Reinstall the spark plug, but leave the spark plug wire disconnected. Air Filter: Clean the air filter. Hoses and Pump: Flush the injection hose with clean water for 1-2 minutes. Remove all hoses. Empty the pump by pulling on the recoil starter about 6 times. This should remove most of the liquid from the pump. .WARNING: Ensure all engine covers and all engine parts are completely and properly reassembled before starting engine. Failure to correctly reassemble engine may result in serious injury or property damage. PREPARING FOR USE AFTER STORAGE n Pull the recoil starter grip three or four times to clean oil from the combustion chamber. n Remove spark plug from the cylinder. Wipe oil from the spark plug and return it to the cylinder. n Reconnect the spark plug wire. n Refuel the machine as described earlier in the operator’s manual. MAINTENANCE TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start No fuel in tank Fill tank Spark plug shorted or fouled Replace spark plug Spark plug is broken (cracked porcelain or electrodes broken) Replace spark plug Ignition lead wire shorted, broken, or disconnected from spark plug Replace lead wire or attach to spark plug Ignition inoperative Contact authorized service center Engine hard to start Water in gasoline Drain entire system and refill with fresh fuel Weak spark at spark plug Contact authorized service center Engine lacks power Dirty air filter Clean or replace air filter Detergent fails to mix with spray Detergent injection hose is not properly submerged Insert injection hose into detergent container or detergent bottle H...