Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Safety instructions marked with this symbol must be observed to pre vent danger to persons. This symbol is be observed to • used to mark safety instruc.. tions that must prevent damage to the machine and its performance. This symbol indicates tips and instructions to simplify work and to ensure a safe operation. Do not let children or people who have not read the instruction manual ope rate the machine. Before starting up your machine please check it carefully for any defects. If you find any, do not start up your machine and contact your Nilfisk distributor. Especially check: ..The insulation of the electric cable should be faultless and without any cracks. If the electric cable is damaged, an authorized Nilfisk distributor should replace it. WARNING! • High pressure jets can be dangerous. Never direct the water jet at persons, pets, live electrical equipment or the machine itself. • Never try to clean clothes or footwear on yourself or other persons. • Hold the spray lance firmly with both hands. The spray lance is affected by a thrust of up to 16.4 N during operation. • The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation. Wear goggles during operation. • Never use the machine in an environment where there could be a danger of explosion. If any doubt arises, please contact the local authorities. • It is not allowed to clean asbestos- containing surfaces with high pressure. .. This high pressure washer must not be used at temperatures below 0°C. .. Never let any persons stay under the product when stored on the wall. WARNING! Inadequate extension cables can be dangerous. Cables on drums should always be completely unwinded to prevent the cable from overheating. 3 Extension cables should be of a watertight construction and comply with the below-mentioned requirements for length and cable dimensions. 1.0 mm. max. 12.5 m 1.5 mm. max. 20 m 2.5 mm. max. 30 m • Cable connections should be kept dry and off the ground. Mains power connection The following should be observed when connecting the high pressure washer to the electric installation: • Only connect the machine to an installation with earth connection. • The electric installation shall be made by a certified electrician. • It is strongly recommended that the electric supply to this machine should include a residual current device (GFCI). Water connection Connection to the public mains according to regulations. This high pressure washer is only allowed to be connected with the drinking water mains, when an appropriate backflow preventer has been installed, Type BA according to EN 1717. The backflow preventer can be ordered under number 106411177. The length of the hose between the back- flow preventer and the high pressure washer must be at least 10 metres to absorb possible pressure peaks (min diameter . inch). Operation by suction (for example from a rainwater vessel) is carried out without backflow preventer. Recommended suction set: 126411387. As soon as water has flown through the BA valve, this water is not considered to be drinking water any more. 2 Description 2.1 Application This high-pressure washer has been developed for domestic use within: - Car, motorbike, boat, caravan, trailer, patio/drive/flagstones, woodwork, brickwork, barbecue, garden furniture, lawn mower Section 5 describes the use of the high-pressure washer for vaious cleaning jobs. IMPORTANT! Only use water without any impurities. If there is a risk of running sands in the inlet water (i.e. from your own well), an additional filter should be mounted. Repair and maintenance WARNING! Always remove the electric plug from the socket before carrying out maintenance work on the machine. Safety devices Locking device on spray gun (7a) (see foldout at the end of this manual): The spray gun features a locking device. When the pawl is activated, the spray gun cannot be ope rated. Thermal sensor: A thermal sensor protects the motor against overloading. The machine will restart after a few minutes when the thermal sensor has cooled. Pressure safety device An integrated hydraulic safety valve protects the system from excessive pressure. Only use the high-pressure washer for purposes described in this manual. The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries. 4 5 2.2 Operation elements and model survey See illustration at the end of this manual. 1 Start/stop switch 2 Water inlet (with fi lter) 3 High pressure connection (only models without hose reel) 4 High pressure hose 5 Electric cable 6 Click & Clean spray lance 7 Spray gun with lock 8 Click & Clean Tornado® PR nozzle 9 Click & Clean Powerspeed® nozzle 10 Click & Clean foam sprayer 11 Nozzle cleaning tool 12 Trolley handle (telescopic handle) 13 Hose reel (not standard) 14 Hose hook 15 Model tag 16 Quick coupling 17 Button for telescopic handle 18 T...
Эта инструкция также подходит к моделям:Моечное оборудование - E 140.2 (3.6 mb)
Моечное оборудование - E 145.2 (3.6 mb)