Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOTTREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! Relieve system pressure before attempting maintenance or disassembly of equipment. Never place hands in front of nozzle. Direct spray away from self and others. Make sure hose and fittings are tightened and in good condition. Never hold onto the hose or fittings during operation. Do not allow hose to contact muffler. Never attach or remove wand or hose fittings while system is pressurized. Use only hose and high pressure accessories rated for 2400 PSI service To relieve system pressure, shut off engine, turn off water supply, and pull gun trigger until water stops flowing. ЕЖШЖ RISK OF CHEMICAL BURN Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any kind of flammable solvent with this product could result in serious injury or death. Do not use acids, gasoline, kerosene, or any other flammable materials in this product. Use only household detergents, cleaners and degreasers recommended for use in pressure washers. Wear protective clothing to protect eyes and skin from contact with sprayed materials. A IMPORTANT SAFETY INSTRUCTIONS (cont’d) HAZARD WHAT CAN HAPPEN HOWTO PREVENT IT ИГа HOT SURF a ACES • Contact with hot surfaces, such as engines exhaust components, could result in serious burn. • During operation, touch only the control surfaces of the pressure washer. Keep children away from the pressure washer at all times. They may not be able to recognize the hazards of this product. International Symbols ЖШ Safety Alert Read Owner's Manual Ö] On ОН (Щ) Stop Fuel Shiitoff »' Fuel X Choke The powerful spray from your pressure washer is glass, automobile paint, auto stripping and trim, ar check the item to be cleaned to assure yourself tha Avoid the use of the concentrated spray stream ex Operating unit with water supply shut off without flo this pressure washer for more than 2 minutes withoi heated (recirculated) water to exit. Running the pre capable of cau: id delicate objec t it is robust eno cept for very stn w of water will re jt pulling the trig ssure washer wi sing damage to fragile surfaces such as: wood, :ts such as flowers and shrubs. Before spraying, ugh to resist damage from the force of the spray, ong surfaces like concrete and steel. ;sult in equipment damage. You should never run ger to allow cool water to enter the pump and the th water supply shut off will void your warranty. ASSEMBLY Carton Contents ' Main Unit pressure washer with wheels Handle • High Pressure Hose • Chemical Pickup Hose and Filter • Gun • Wand Main Unit Pressure Washer with Wheels High Pressure Hose ÏCCP- Chemical Pickup Hose and Filter Gun and Wand Bag Containing • Video Cassette • Owner's Manual • Nozzle Cleaning Kit and Replacement O-Rings • Engine Oil • Rubber Isolator and Mounting Hardware • Handle Mounting Hardware a Video Cassette Owner's Manual Nozzle Cleaning Kit Í •» Handle Mounting Hardware Engine Oil 0 w f Rubber Isolator and Mounting Hardware Replacement O-Rings 5 Tools Required for Assembly Adjustable wrench '?n wrench Remove Pressure Washer from Carton • Open carton from the top. Locate and remove from box the handle, gun, wand, videotape, and oil. • Cut carton along dotted lines. • Remove all carton inserts. • Roll unit through opening in carton. NOTE: The hose is located at the bottom of the box. Preparing the Pressure Washer for First Use Note: Included with your pressure washer is a video cassette tape on how to prepare your unit for operation. It is recommended you view this tape before performing the next steps. 1. Insert handle onto frame. « Insert knobs into the threaded slot in front of the frame handle and tighten by turning in a clockwise direction. • Slide bolts into the slot in the side of the frame handle and tighten the nuts by turning in a clockwise direction. Insert boit and tighten lock nut. Tighten knob in clockwise direction. Using an adjustable wrench, remove nut from bolt that attaches board to frame. Remove wood plank from the frame of the unit. Discard bolt and board. 3. Mount the rubber isolator to the frame. To mount isolator place threaded end of bolt through the washer. • Next with washer on bolt place threaded end of bolt through the larger hole in bottom of the rubber isolator. • Place threaded portion of bolt through the same hole location the wood plank was mounted to on the pressure washer. • Next place the tee nut over the threaded portion of the bolt and use the Allen wrench provided to tighten isolator to the frame. TEE NUT PRESSURE WASHER FRAME -ISOLATOR Ij 'washer 4. Connect wand extension to gun. To tighten, turn knob in clockwise direction. Hand tighten. --- 5. Remove tie wrap off of high pressure hose. Unwind high pressure hose and attach the threaded end to the gun. Tighten with adjustable wrenc...