Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Repeat if necessary. If the engine does not start after two pulls, pull the trigger to relieve the pressure. 11. If the choke was used to start the engine, move the choke lever to the OFF position. 12. Depress trigger on gun to start water flow. NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick back when triggered. 13. Release trigger to stop water flow. 14. Adjust nozzle spray for the task being performed. See How To Use Spray Wand instructions in this section. DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. MAINTENANCE When performing maintenance, you may be exposed to hot surfaces, water pressure, or moving parts that can cause serious injury or death! Before performing any maintenance or repair, disconnect spark plug wire, let engine cool and release all water pressure. The engine contains flammable fuel. DO NOT smoke or work near open flames while performing maintenance. To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high-temperatures or dusty conditions, more frequent maintenance checks will be required. 13- ENG . CUSTOMER RESPONSIBILITIES TABLE MAINTENANCE TASK Before each use Every 25 hours or yearly Every 50 hours or yearly Every 100 hours or yearly ENGINE check oil level X change oil X check air filter X clean/replace spark plug X PRESSURE WASHER check/clean inlet screen X check high pressure hose X check soap and chemical hose and filter X check gun and wand for leaks X prepare for storage Prepare unit for storage if it is to remain idle for longer than 30 days ENGINE To Check Oil 1. Shut down engine and place on a level surface. 2. Remove filler cap/dipstick and wipe it clean. Filler cap/dipstick 3.Insert and remove the filler cap/dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. Oil Filler Cap/Dipstick Upper Limit Lower Limit 4. If the oil level is low, fill to the edge of the oil filler hole with the SAE 10W-30 oil. NOTE: Other viscosities shown in the chart may be used when the average temperature in your area is within the recommended range. SAE Viscosity Grades ** * Synthetic 5W-30, 10W-30 F-20 0 20 3240 60 80 100 C-30-20 -10 0 10 20 30 40 STARTING TEMPERATURES RANGE ANTICIPATED BEFORE NEXT OIL CHANGE . 14- ENG To Change Oil Drain the engine oil when the engine is warm. Warm oil drains quickly and completely. 1. Turn the fuel valve to the OFF position, 1/4 turn clockwise. 2. Place a suitable container next to the engine to catch the used oil. 3. Remove filler cap/dipstick and drain the oil into the container by tipping the engine toward the oil filler neck. Oil Filler Cap/Dipstick Upper Limit Lower Limit Oil Filler Neck NOTE: Please dispose of used motor oil in a manner that is compatible with the environment. It is recommended to take used oil in a sealed container to your local recycling center or service station for reclamation. Do not throw it in the trash or pour it on the ground or down a drain. 4. With the engine in a level position, fill to the upper limit mark on the dipstick with SAE 10W-30 oil. Engine oil capacity is 0.58 quart (.055 liter). NOTE: Other viscosities shown in the chart in the “To Check Oil” paragraph may be used. 5. Replace the oil filler cap/dipstick securely. Air Cleaner A dirty air cleaner will restrict air flow to the carburetor and cause poor engine performance. Inspect the filter each time the engine is operated. Clean the filter more frequently if the engine is operated in very dusty areas. NOTICE: Operating the engine without a filter, will allow dirt to enter the engine, causing rapid engine wear. This type of damage is not covered under the warranty. Inspect 1. Press the latch tabs on the top of the air cleaner cover and remove the cover. Check the filter to be sure it is clean and in good condition. 2. Reinstall the filter and air cleaner cover. Air Cleaner Body Filter Air Cleaner Cover Latch Tabs Lower Tabs Air Duct Cleaning 1. Tap the filter several times on a hard surface to remove dirt or blow compressed air [not exceeding 30 psi (207kPa, 1.2 kg/cm2) through the filter from the clean side that faces the engine. Never try to brush off dirt. Brushing will force dirt into the fibers. 2. Wipe dirt from the air cleaner body and cover using a moist rag. Be careful to prevent dirt from entering the air duct that leads to the carburetor. 15- ENG . Clean and Replace Spark Plug Change the spark plug every 100 hours of operation or once each year, whichever comes first. This will help your engine to start easier and run better. Resistor .030” (0.76 MM) Wire Gauge PUMP This screen filter should be checked periodically and cleaned if necessary. 1. Remove filter by grasping end and removing it from water inlet of pump as shown. 2. Clean filter by flush...
Эта инструкция также подходит к моделям:Моечное оборудование - D28235 (1.68 mb)