Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adapter with this product. WARNING: To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with wet hands. GROUND FAULT CIRCUIT INTERRUPTER PROTECTION This pressure washer is provided with a Ground Fault Circuit Interrupter (GFCI) built into the power supply cord. This device provides additional protection from the risk of electrical shock. Should replacement of the plug or cord become necessary, use only identical replacement parts that include GFCI protection. See Figure 13 for testing procedure. WARNING: Connect directly to outlet. Do not use with extension cord. The use of an extension cord will override the GFCI built into the plug of the power supply cord resulting in the risk of electrical shock. • The label on your tool may include the following symbols. V..............volts A..............amperes Hz............hertz W ............watts min ..........minutes ............alternating current ........direct current no ............no load speed ............Class II Construction …/min......revolutions or reciprocation per minute ............earthing terminal ............safety alert symbol SAVE THESE INSTRUCTIONS 3 Upper Cord Wrap Hook Assembly - PW1600 Insert cord wrap top hook (M) into the rear slot in handle (K), pushing down firmly until it stops. Drive two 1 1/2” self tapping screws included in cord hook bag through handle holes into cord wrap hook as shown until tight. DO NOT over tighten. PW1750 ASSEMBLY: Tools Required: Philips screwdriver Adjustable wrench Hardware Bag Contents: - 2 pcs. flat washers - 2 pcs. hex locking nuts Wheel Assembly - PW1750 Remove the 2 protective plastic end caps from axle and discard. Place wheel (E) with 5 raised square bumps facing outwards as shown below over threaded axle end, followed by flat washer, and hex locking nut. Using wrench, tighten nut securely. Align 5 square knotches in wheel cap (E1) to raised PW1600 1 3 4 2 “UP” Label UNIT ASSEMBLY PW1600 ASSEMBLY: Tools Required: Philips screwdriver Adjustable wrench Hardware Bag Contents: - 2 pcs. flat washers - 2 pcs. hex locking nuts - 6 pcs. 5/8” screws Wheel Assembly - PW1600 Remove the 2 protective plastic end caps from axle and discard. Place wheel (E), flat washer, and hex locking nut over axle end as shown with smooth face of wheel having circular holes only facing outwards (side of wheel with raised spokes faces inwards toward pressure washer body). Using a wrench, tighten nut securely. Align wheel cap (E1) over wheel face as shown and press center of wheel cap until it snaps securely to wheel. Handle Assembly - PW1600 1.) With rectangular steel tube (N) ends pointing upwards as labeled, push tubes down firmly into rectangular holes in black top housing (P) until they hit bottom. 2.) Drive one 5/8” screw through the hole in each side of the orange housing (Q) as shown and into the tapped hole of the tube until tight. 3.) Next drive one 5/8” screw through each hole in the upper back side of the black top housing (P) as shown into the tapped hole of the tube until tight. 4.) You are now ready to align the rectangular holes in bottom of handle (K) over the tubes, pushing the handle down until it’s bottom edge slides into black housing (P) fully. Drive one 5/8” screw through each hole in the back of the handle (K) as shown into the tubes until tight to complete handle assembly. 4 A. High pressure water outlet (OUTLET) B. Pump Quick Connector C. High pressure turbo wand D. Adjustable fan wand E. Wheels E1. Wheel Cap F. Gun F1. High pressure hose connector F2. Gun safety catch G. Power supply cord with GFCI H. Hardware bag I. On/off switch J. Garden hose Quick Connector K. Handle L. Removable detergent tank with cap M. Cord wrap top hook N. Steel Support tubes O. Nozzle Cleaning tool P. Black top housing Q. Orange main housing F F1 F2 H O I I K L J M N O B E1 E D P Q C O I E1 F F1 F2 I K L J H M O D C E G N Q A P B PW1600 PW1750 5 2 1 PW1600 3 PW1600 IMPORTANT: The outer brass ring on the garden hose quick connector MUST be pulled back fully as shown in Fig. 11b) before pushing it over the pump quick connector (B). Water will not flow through to the pump if these 2 connectors are not fully coupled. Figure 12 - Connect other end of garden hose to the cold water source and turn water on full. This pressure washer is not intended to pump hot water. Never connect it to a hot water supply as it will significantly reduce the life of the pump. OPERA...
Эта инструкция также подходит к моделям:Моечное оборудование - PW1600 (2.23 mb)
Моечное оборудование - PW1750 (2.23 mb)