Войти:
Оценок - 2, средний балл: 3.5 ( )

Инструкция по эксплуатации Graco Inc., модель PCH2425

Производитель: Graco Inc.
Размер: 1.54 mb
Название файла:
Язык инструкции:
Перейти к скачиванию



Фрагмент инструкции


When there is a steady stream of water present, turn water source off. Reconnect water source to pump inlet and turn on water source. Squeeze trigger to remove remaining air. 8. Move choke to the "No Choke" position. 9. Move throttle control lever to the "Fast" position. 10. Use high pressure hose under 100 feet. Will not draw chemicals 7. Chemical build up in chemical injector. 1. Wand not in low pressure. 2. Chemical filter clogged. 3. Chemical screen not in chemical 4. Chemical adjustment knob closed. 5. Chemical too thick 6. Pressure hose is too long 2. Clean filter. 3. Insure end of chemical hose is fully submerged into chemical. 4. Turn knob fully counterclockwise to open. 5. Dilute chemical. Chemical should be the same consistency as water. 6. Lengthen water supply hose instead of pressure hose. 7. Have parts cleaned or replaced by AWSC. 1. See How to Use Wand paragraph in the Operation Section. 17 — ENG D22885 PROBLEM CAUSE CORRECTION No or low pressure (after 1. Worn seal or packing. 1. Have replaced by AWSC. period of normal use.) 2. Worn or obstructed valves. 3. Worn unloader piston. 4. Worn E-Z start valve. 2. Have replaced by AWSC. 3. Have replaced by AWSC. 4. Have replaced by AWSC. Water leaking at gun/wand connection 1. Worn or broken o-ring. 2. Loose hose connection. 1. Check and replace. 2. Tighten. Water leaking at pump 1. Loose connections. 2. Piston packings worn. 3. Worn or broken o-rings. 4. Pump head or tubes damaged from freezing. 1. Tighten. 2. Have replaced by AWSC. 3. Have replaced by AWSC. 4. Have replaced by AWSC. Oil leaking at pump 1. Oil seals worn. 1. Have replaced by AWSC. (if applicable) 2. Loose drain plug. 3. Worn drain plug, o-ring (if applicable). 4. Worn fill plug o-ring. 5. Pump overfilled. 6. Incorrect oil used. 7. Vent plug is clogged. 2. Tighten. 3. Check and replace. 4. Check and replace. 5. Check for correct amount. 6. Drain and fill with correct amount and type of oil. 7. Clean vent plug; blow air through it to remove any blockage. If problem persists, replace plug. 18 — ENG D22885 LIMITED WARRANTY Porter-Cable Corporation warrants to the original purchaser that each new pressure washer, service part, and accessory is free from defects in material and workmanship, and agrees to repair or replace under this warranty any defective product or part as follows from the original date of purchase. 1 Year -Consumer applications (i.e. personal residential household usage only). 90 Day -Commercial applications (income producing). Engine warranties are the responsibility of the engine manufacturer. WARRANTY SERVICE is available by delivering or shipping the defective product or part to any Porter- Cable authorized warranty service location. To determine the nearest authorized warranty service location, call the toll free number, 1-888-559-8550, 24 hours a day, 7 days a week. Specific instructions regarding servicing arrangements and scheduling ma...

Эта инструкция также подходит к моделям:
Моечное оборудование - D22885-011-0 (1.54 mb)
Моечное оборудование - D22885-011-0 (1.54 mb)
Моечное оборудование - D22885-011-0 (1.54 mb)
Моечное оборудование - D22885-011-0 (1.54 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории