Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Perform these tasks to prepare unit for operation: • Attach the handle to the main unit. • Add oil to the engine. • Add fuel to the fuel tank. • Connect the high pressure hose to the spray gun and the pump. • Connect the water supply to the pump. • Connect nozzle extension to spray gun. • Select and install desired nozzle (if applicable). Attach Handle to Unit This manual describes assembly and use of three models (01805, 01806 and 01936). Please see the appropriate section for the handle instruction specific to your model. To attach handle with accessory tray (Models 01805 and 01806): NOTE: All assembly operations given in this section will be described from the perspective of assembling the pressure washer from the rear. 1. Slide plastic accessory tray onto handle and align holes in accessory tray with holes on handle (Figure 1). Figure 1 — Attach Accessory Tray 2.Secure tray to handle with self tapping screws using a #2 phillips screwdriver. Ensure screws are tight but not crushing the plastic accessory tray. 3.Place handle assembly onto handle supports connected to main unit. Make sure holes in handle align with holes on handle supports (Figure 2). Align Holes Handle Handle Supports Figure 2 — Attach Handle to Base NOTE: It may be necessary to move handle supports from side to side in order to align handle so it will slide over handle supports. 5 Pressure Washer 6 4. Insert “L” bolt through hole on left side of handle (viewing from rear of unit) and attach plastic knob. Tighten knob by hand (Figure 3). 5. Insert carriage bolt through right side hole from outside of unit and attach plastic knob from inside of unit (viewing from rear of unit).Tighten by hand (Figure 3). 6. Insert “J” hook into second from left slot in accessory tray (Figure 4). 7. Pinch chemical hose and slide it into metal clip as shown in Figure 5. 8. Tilt unit up by handle and attach metal clip to rib on center underside of accessory tray (Figure 6). Slide chemical hose through metal clip so that it is tight but not kinked. Figure 3 — Secure Handle Figure 4 — Install “J” Hook on Accessory Tray Figure 5 — Slide Chemical Hose into Metal Clip Figure 6 — Slide Metal Clip onto Accessory Tray Flange Pressure Washer To attach handle supplied with two “L” hooks (Model 01936): 1. Place handle assembly onto handle supports connected to main unit. Make sure holes in handle align with holes on handle supports (Figure 7). Align Holes Handle Handle Supports Figure 7 — Attach Handle to Base NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. 2. Insert carriage bolts through holes from outside of the unit and attach a plastic knob from inside of unit (Figure 8).Tighten by hand. Figure 8 — Secure Handle 3. Insert one “L” hook through hole just under billboard on left side of handle (viewing from rear of unit). Hold hook in place with pliers and attach locknut with 7/16” wrench (Figure 9). Add Engine Oil IMPORTANT: Any attempt to crank or start the engine before it has been properly serviced with the recommended oil may result in an engine failure. • Place pressure washer on a level surface. • Refer to engine owners manual to add recommended oil to engine. NOTE: Check Oil Often During Engine Break–in. Add Fuel WARNING! NEVER fill fuel tank indoors. NEVER fill fuel tank when engine is running or hot.Allow unit to cool for two minutes before refueling. DO NOT light a cigarette or smoke when filling the fuel tank. WARNING! DO NOT overfill the fuel tank. Always allow room for fuel expansion. • Place pressure washer on a level surface. • Refer to engine owners manual to add recommended fuel to engine. Hose Hook Spray Gun Hook Figure 9 — Attach “L” Hooks to Handle 4.Insert other “L” hook through hole just above billboard on right side of handle (viewing from rear of unit). Hold hook in place with pliers and attach locknut with 7/16” wrench (Figure 9). 7 Pressure Washer 8 Connect Hose and Water Supply to Pump IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine. 1. Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 12).Tighten by hand. 2. Attach other end of high pressure hose to high pressure outlet on pump (Figure 13).Tighten by hand. 3. Before connecting garden hose to water inlet, inspect inlet screen (Figure 14). Clean screen if it contains debris or replace if damaged. Refer to “O-Ring Maintenance” section on page 13 if inlet screen is damaged. DO NOT run pressure washer if inlet screen is damaged. 4. Run water through your garden hose for 30 seconds to clean out any debris. IMPORTANT: DO NOT siphon standing water for the water supply. Use ONLY cold water (less than 100°F). 5. Connect garden hose (not to exceed 50 feet in length) to water inlet.Tighten by hand (Figure 14). CAUTION! There MUST be at least ten feet of unrestricted garden hose between t...