Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Automatic Cool Down System — Cycles water through pump when water reaches 125°-155°F.Warm water will discharge from pump onto ground.This system prevents internal pump damage. Chemical Injection Siphon/Filter — Use to siphon detergent or other pressure washer chemicals into the low pressure stream. Choke Lever — Prepares a cold engine for starting. Fuel Tank — Fill tank with regular unleaded pressure washer. Always leave room for fuel expansion. Fuel Valve — Used to turn fuel on and off to engine. High Pressure Hose — Connect one end to the water pump and the other end to the spray gun. High Pressure Outlet — To connect high pressure hose. Nozzle Extension with Quick Connect — Allows you to switch between four different spray tips. Oil Fill Cap — Fill engine with oil here. Pump — Develops high pressure. Recoil Starter — Use for starting the engine manually. Safety Goggles (not shown) — Always use the enclosed goggles or other eye protection when running your pressure washer. Spray Gun — Controls the application of water onto cleaning surface with trigger device. Includes safety latch. Spray Tips — Chemical injection, 0°, 15°, and 40°: for various high pressure cleaning applications. Throttle Lever—Sets engine in starting mode for recoil starter and stops a running engine. Water Inlet — Connect garden hose here. High Pressure Hose SpeedClean™ 2800 PSI Pressure Washer SpeedClean™ 2800 PSI Pressure Washer ASSEMBLY IMPORTANT: Read entire owner’s manual before you attempt to assemble or operate your new pressure washer. Remove Pressure Washer From Carton 1. Remove the parts bag, accessories, and inserts included with pressure washer. 2. Slice two corners at the end of carton from top to bottom so the panel can be folded down flat. 3. Remove pressure washer from carton. Carton Contents Items in the carton include: • Main Unit • Safety Goggles • Handle • High Pressure Hose • Spray Gun • Nozzle Extension with Quick Connect Fitting • Oil Bottle • Parts Bag (which includes the following): • Owner’s Manual • Engine Manual • Owner’s Registration Card • Bag containing 4 multi–colored Quick Connect Nozzles • Handle Fastening Hardware Kit (which includes): • Carriage Bolts (2) • Plastic Knobs (2) • “L” Bolts (2) • Lock Nuts (2) PREPARING PRESSURE WASHER FOR USE If you have any problems with the assembly of your pressure washer or if parts are missing or damaged, call the pressure washer helpline at 1-800-743-4115. If calling for assistance, please have the model, revision, and serial number from the data tag available. Perform these tasks to prepare unit for operation: 1. Fill out and send in registration card. 2. Attach handle to main unit. 3. Add oil to engine crankcase. 4. Add fuel to fuel tank. 5. Connect high pressure hose to spray gun and pump. 6. Connect water supply to pump. 7. Attach nozzle extension to spray gun. 8. Select/attach quick connect spray tip to nozzle extension. Attach Handle to Unit NOTE: All assembly operations given in this section will be described from the perspective of assembling the pressure washer from the rear. 1. Place handle assembly onto handle supports connected to main unit. Make sure holes in handle align with holes on handle supports (Figure 1). Align Holes Handle Handle Supports Figure 1 — Attach Handle to Base NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. 6 SpeedClean™ 2800 PSI Pressure Washer 2. Insert carriage bolts through holes from outside of the Add Engine Oil and Fuel unit and attach a plastic knob from inside of unit • Place pressure washer on a level surface. (Figure 2).Tighten by hand. Figure 2 — Secure Handle CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. • Refer to engine manual for oil and fuel fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. 3. Insert one “L” hook through hole just under billboard on left side of handle (viewing from rear of unit). Hold hook in place and attach a plastic knob from inside of unit (Figure 3).Tighten by hand. Hose Hook Spray Gun Hook Figure 3 — Attach “L” Hooks to Handle 4.Insert other “L” hook through hole just above billboard on right side of handle (viewing from rear of unit). Hold hook in place and attach a plastic knob from inside of unit (Figure 3).Tighten by hand. • Refer to engine owner’s manual and follow oil and fuel recommendations and instructions. NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations. Connect Hose and Water Supply to Pump IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine. 1. Uncoil high pressure hose and attach one end of hose to base of spray gun (Figure 4).Tighten by hand. Figure 4 — Connect High Pressure Hose to Spray Gun 7 Sp...