Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Using 2mm (5/64) allen wrench, remove orifice from end of nozzle extension (Figure 23). 3. Remove in-line filter from other end of nozzle extension. 4. Use small diameter wire or a small paper clip to free any foreign material clogging or restricting orifice (Figure 23). 5. Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 24). Back flush between 30 to 60 seconds.Turn adjustable nozzle extension to stream spray and move nozzle from low to high while flushing. 6. Reinstall orifice and in-line filter into nozzle extension. DO NOT overtighten orifice with allen wrench. 7. Reattach nozzle extension to spray gun. 8. Reconnect water supply, turn on water, and start engine. 9. Test pressure washer by operating with nozzle in high and low positions. Quick-connect spray tips: 1. Shut off engine and turn off water supply. 2. Remove spray tip from end of nozzle extension (Figure 25). 3. Remove in-line filter from other end of nozzle extension. 4. Use small diameter wire or a small paper clip to free any foreign material clogging or restricting spray tip (Figure 25). 5. Using a garden hose, remove additional debris by back flushing water through nozzle extension (Figure 26). Back flush between 30 to 60 seconds. 6. Reinstall spray tip and in-line filter into nozzle extension. 7. Reattach nozzle extension to spray gun. 8. Reconnect water supply, turn on water, and start engine. 9. Test pressure washer by operating with each Quick Connect spray tip. Orifice Figure 23 — Removing and Cleaning Orifice Figure 24 — Backflushing the Nozzle Use wire here to remove debris. Figure 25 — Nozzle Maintenance Figure 26 — Backflushing the Nozzle Extension Pressure Washer 14 Purge Pump of Air and Contaminants To remove air from the pump, follow these steps: 1. Set up pressure washer as described in “Preparing Pressure Washer For Use”. Connect water supply and turn water on. 2. Pull trigger on spray gun and hold. 3. When water stream is steady and constant, engage safety latch. To remove contaminants from the pump, follow these steps: 1. Set up pressure washer as described in “Preparing Pressure Washer For Use”. Connect water supply and turn water on. 2. Remove nozzle extension from spray gun. 3. Start engine. 4. Squeeze trigger on spray gun and hold. 5. When water stream is steady and constant, engage safety latch and refasten nozzle extension. O–Ring Maintenance O-Rings keep the connections of the hoses and spray gun tight and leak–free.Through normal operation of the pressure washer, they may become worn or damaged. An O–Ring Maintenance Kit is provided with the pressure washer which includes replacement o-rings, rubber washer and water inlet filter. Refer to the instruction sheet provided in the kit to service the o-rings. Note that not all of the parts in the kit will be used on your unit. To remove a worn or damaged o–ring; use a small flathead screwdriver to get underneath the o-ring and pry it off. Pump Maintenance NOTE: Model 01806 (2650 PSI) does not require any pump maintenance.The pump is pre-lubricated and sealed, requiring no additional lubrication for the life of the pump. For Model 01805 (2500 PSI) & 01936 (2550 PSI): Changing Pump Oil Change oil every 50 hours or once yearly, whichever occurs first. NOTE: Purchase a premeasured bottle of pump oil, item number 190585GS, by contacting nearest authorized service center. Change pump oil as follows: 1. Drain engine oil and fuel from pressure washer. 2. Use 8mm allen wrench to remove black oil cap from pump. It’s found between high pressure outlet and garden hose inlet (Figure 27). 3. Tilt pressure washer to drain oil into an approved container until it drips slowly from the pump. 4. Tilt pressure washer in opposite direction and empty premeasured pump oil bottle into same opening (a small funnel may be helpful). 5. Install black oil cap on pump and tighten firmly. 6. Set pressure washer in upright position.Add fuel and engine oil. ENGINE MAINTENANCE See the engine owner’s manual for instructions on how to properly maintain the engine. CAUTION! Avoid prolonged or repeated skin contact with used motor oil. Used motor oil has been shown to cause skin cancer in certain laboratory animals.Thoroughly wash exposed areas with soap and water. CAUTION! KEEP OUT OF REACH OF CHILDREN. DON'T POLLUTE. CONSERVE RESOURCES. RETURN USED OIL TO COLLECTION CENTERS. Oil Cap Figure 27 - Changing Pump Oil Pressure Washer Pressure Washer PREPARING THE UNIT FOR STORAGE Water should not remain in the unit for long periods of time. Sediments or minerals can deposit on pump parts and “freeze” pump action. If you do not plan to use the pressure washer for more than 30 days, follow this procedure: 1. Flush chemical injection hose by placing filter into a pail of clean water while running pressure washer in low pressure mode. Flush for one to two minutes. 2. Shut off engine and let it cool, then remove high pressure and garden hoses. Disconnect spark plug ...
Эта инструкция также подходит к моделям:Моечное оборудование - 01806 (2.38 mb)