Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
4. Make sure black spray tip is installed. NOTE: Detergent cannot be applied with high pressure spray tips (White, Green,Yellow, or Red). Figure 10 — Spray Tips Black Low Pressure Use to apply detergent White 40° Green 25° Yellow 15° High Pressure Red 0° 12 Section 4: Operation 5. Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump; start engine. 6. Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes. DO NOT allow detergent to dry on (prevents streaking). 7. Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. Pressure Washer Rinsing After you have applied detergent, scour the surface and rinse it clean as follows: 1. Apply trigger lock to spray gun. 2. Remove black chemical spray tip from nozzle extension. 3. Select and install desired high pressure spray tip following the instructions in “How to Use Spray Tips”. 4. Keep spray gun a safe distance from the area you plan to spray. WARNING High pressure spray could cause you to fall if you are too close to the cleaning surface. • Keep spray nozzle between 8 to 24 inches away from cleaning surface. • Operate this unit on a stable surface. • Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location. • Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back. 5. Increase or decrease spray pressure by turning pressure control knob counterclockwise or clockwise respectively (Figure 11). Use lower pressure to wash items such as a car or boat. Use higher pressure to strip paint and degrease driveways. Pressure Control Knob Figure 11 — Pressure Control Knob 6. Apply high pressure spray to small area and then check surface for damage. If no damage is found, you can assume it is okay to continue cleaning. 7. Start at top of area to be rinsed, working down with same overlapping strokes as used for cleaning. Cleaning Detergent Siphoning Tube If you used the detergent siphoning tube, you must flush it with clean water before stopping the engine. 1. Place chemical injection siphon/filter in a bucket full of clean water. 2. Attach black low pressure spray tip. 3. Flush for 1-2 minutes. 4. Shut off engine. IMPORTANT: Simply shutting OFF engine will not release pressure in the system. When the engine has shut down, squeeze the trigger on the spray gun to relieve the pressure in the hose. Automatic Cool Down System (Thermal Relief) If you run the engine on your pressure washer for 3-5 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach temperatures above 125°F.The system engages to cool the pump by discharging the warm water onto the ground. 13 Section 5 Maintenance SPECIFICATIONS Check High Pressure Hose Rated Pressure . . . . . . . . . . . . . . . . . . . . . . . . . 3,400 PSI Flow Rate . . . . . . . . . . . . . . 3.2 gallons per minute (gpm) Detergent Use detergent approved for pressure washers Water Supply Temperature . . . . . . . . . . . . . . . . . Not to exceed 100°F Automatic Cool . . . . . . . . . . . . .Will cycle when water Down System reaches 125°-155°F Shipping Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 135 lbs. GENERAL MAINTENANCE RECOMMENDATIONS The pressure washer warranty does not cover items that have been subjected to operator abuse or negligence.To receive full value from the warranty, the operator must maintain the pressure washer as instructed in this manual. NOTE: Should you have questions about replacing components on your pressure washer, please call 1-800-743-4115 for assistance. • Some adjustments will need to be made periodically to properly maintain your high pressure washer. • All maintenance in this manual and the engine operator’s manual should be made at least once each season. • If equipped with inflatable tires, keep the air pressure at the value marked on the tire or within 15 and 40 psi. Before Each Use 1. Check engine oil level. 2. Check water inlet screen for damage. 3. Check in-line filter for damage. 4. Check high pressure hose for leaks. 5. Check detergent siphoning tube and filter for damage. 6. Check spray gun, nozzle extension, and nozzles for leaks. 7. Rinse out garden hose to flush out debris. PRESSURE WASHER MAINTENANCE Check and Clean Inlet Screen Examine the screen on the water inlet. Clean it if the screen is clogged or replace it if screen is damaged. The high pressure hose can develop leaks from wear, kinking, or abuse. Inspect the hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, damage or movement of couplings. If any of these conditions exist, replace the hose immediately. WARNING The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to se...