Оценок - 3, средний балл: 5 ( )

Производитель: Graco Inc. Размер: 536.58 kb Название файла: 08b6e4ff-f7aa-4c38-aa2b-9326ee5cb265.pdf Язык инструкции:

8. Install the capscrews and washers finger–tight. Torque the screws to 21.7 ft–lb (29 Nm) following the tightening pattern (Figure 4). Uneven tightening may cause the manifold to bind or jam. 1 4 23 5 8 7 6 3. Carefully examine each plunger for any scoring or Figure 4 cracking and replace as necessary. . . Servicing the V–Packings 5. Thoroughly clean the packing cavities and examine. NOTE: There are two types of packing kits: one is just packings, the other includes the packings, rings and retainers. 1. Remove the manifold as outlined in the Pumping Section. 2. Carefully pull the packing retainer from the manifold. Examine the o–ring and replace it if it is cut or damaged. 3. Remove the v–packing and head ring. Pull out the intermediate retainer ring. Remove the second v–packing and second head ring. 4. Inspect all parts and replace as necessary. ACCESSORIES (Must be purchased separately) DOWNSTREAM CHEMICAL INJECTOR KIT 800–117 For injecting harsh cleaning chemicals downstream from the pump. UPSTREAM CHEMICAL INJECTOR KIT 800–257 For injecting mild cleaning chemicals upstream into the pump. BACKFLOW PREVENTOR 801–133 Prevent back–up of contaminated water into fresh supply. Install upstream of pump. 6. Lightly grease the packing cavities and then replace the packings in the following order: head ring, v–packing, intermediate ring, head ring, v–packing and packing retainer with the o–ring installed in the retainer groove. CAUTION Be very sure the parts are installed in the proper order and facing the correct direction. See the pump drawing on page 16. Improperly installed parts will cause a malfunction. 7. Reassemble the manifold as instructed in Servicing the Plungers. WATER SANDBLASTING KIT 800–120 For abrasive cleaning of stubborn dirt and paint. Requires a spray tip which is not included in kit (2245 uses 801–666, 3035 uses 801–600, 3040 uses 803–107). ANTI–FREEZE FLUSH KIT 802–327 For flushing system with 50% anti–freeze solution prior to transporting or storing pressure washer in below freezing temperatures. INLET PRESSURE REGULATOR 800–258 Regulates inlet water pressure to 60 psi (4 bar) maximum. TECHNICAL DATA Model 800–062 Model 800–063 Model 800–065 Model 800–335 Engine (all 11 hp, air–cooled, 4 cycle) Wisconsin Robin Briggs and StrattonI/C Wisconsin Robin Honda OHV Gasoline Tank Capacity 6.2 quarts (6 liter) 6 quarts (5.7 liter) 6.2 quarts (6 liter) 6.9 quarts (6.5 liter) Water Pump MaximumWorking Pressure 2200 psi (152 bar) 2200 psi (152 bar) 3000 psi (207 bar) 3000 psi (207 bar) Water Pump Maximum Flow 4.5 gpm (17 lpm) 4.5 gpm (17 lpm) 3.5 gpm (13 lpm) 4 gpm (15 lpm) Inlet Hose Connection 3/4” garden hose (f) 3/4” garden hose (f) 3/4” garden hose (f) 3/4” garden hose (f) Weight 222 lb (101 Kg) 213 lb (97 Kg) 222 lb (101 Kg) 219 lb (100 Kg) Dimensions LengthWidth Height 44” (1118 mm) 31” (787 mm) 28” (711 mm) 44” (1118 mm) 31” (787 mm) 26” (660 mm) 44” (1118 mm) 31” (787 mm) 28” (711 mm) 44” (1118 mm) 31” (787 mm) 26” (660 mm) Maximum Inlet Water Temperature 160. F (70. C) 160. F (70. C) 160. F (70. C) 160. F (70. C) Wetted Parts High Pressure Hose Bypass Hose Pressure Washer (including fittings) Acrylonitrile and Buna–N cover and tube Synthetic yarn and EPDM Anodized aluminum, Aluminum or bronze alloys, Brass Copper, Nylon– composite, Ceramic, Buna–N, Cotton phenolic, 303, 304, and 316 Stainless steel, Polymide–12thermoplastic, , Carbon steel, Zinc with or without yellow chromate plate is a registered trademark of the DuPont Company. (FreeText) (Square) ........... THE GRACO WARRANTY WARRANTY AND DISCLAIMERS Graco warrants all equipment manufactured by it and bearing its name to be free from defects in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. As purchaser’s sole remedy for breach of this warranty, Graco will, for a period of twenty four months from date of sale, repair or replace any part of the equipment proven defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective for examination by Graco to verify the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will b...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: