Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Align the collar on the threaded nipple on the pump. . Insert the nozzle on the end of the high pressure hose collar into the threaded nipple. . Turn the collar clockwise to tighten the hose securely to the pump. . Pull on the hose to be certain it is properly secured. CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER See Figure 8. The water supply must come from a water main. NEVER use hot water or water from pools, lakes, etc. Before connecting the garden hose to the pressure washer: . Run water through the hose for 30 seconds to clean any debris from the hose. . Inspect the screen in the water intake. . If the screen is damaged, do not use the machine until the screen has been replaced. . If the screen is dirty, clean it before connecting the garden hose to the machine. ............To connect the garden hose to the machine: . Uncoil the garden hose. NOTE: There must be a minimum of 10 feet of unrestricted hose between the pressure washer intake and the hose faucet or shut off valve (such as a “Y” shut off connector). . With the hose faucet turned completely off, attach the end of the garden hose to the water intake. Tighten by hand. Fig. 8 Fig. 7 GARDEN HOSE COLLAR THREADED NIPPLE SCREEN WATER INTAKE 13 OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. WARNING: Do not direct discharge stream at persons. Failure to heed this warning could result in serious injury. APPLICATIONS You may use this tool for the purposes listed below: . ..Removing dirt and mold from decks, cement patios, and house siding . ..Cleaning cars, boats, motorcycles, outdoor furniture, and grills STARTING AND STOPPING THE PRESSURE WASHER See Figures 9 - 10. CAUTION: Do not run the pump without the water supply connected and turned on. Before starting the engine: . Connect all hoses. . Check all fluids (oil and gas). . Turn the garden hose on then squeeze the trigger to relieve air pressure; hold the trigger until a steady stream of water appears. To start the engine: . Push primer bulb 3 times. NOTE: If starting the engine for the first time, push the primer bulb 5 times. . Grasp the recoil starter and pull slowly until resistance is felt. Give the recoil starter a short, brisk pull to start the engine. To stop the engine: Press and hold the switch in the OFF position for three (3) seconds or until the engine stops. Fig. 10 Fig. 9 RECOIL STARTER PRIMER BULB 3X OFF SWITCH STOP OPERATION Fig. 11 USING THE SPRAY WAND TRIGGER See Figure 11..... For greater control and safety, keep both hands on the spray wand at all times. . Pull back and hold the trigger to operate the pressure washer. . Release the trigger to stop the flow of water through the nozzle. To engage the lock out: . Push up on the lock out until it clicks into the slot. To disengage the lock out: . Push the lock out down and into its original position. For the most effective cleaning, the spray nozzle should be between 8 in. and 24 in. from the surface to be cleaned. If the spray is too close it can damage the cleaning surface. SELECTING THE RIGHT QUICK-CONNECT NOZZLE FOR THE JOB See Figure 12 - 13. ............Before starting any cleaning job, determine the best nozzle for the job. Each of the three nozzles has a different spray NOZZLE “CLICK” SLOT LOCK OUT OPERATION Fig. 11 USING THE SPRAY WAND TRIGGER See Figure 11..... For greater control and safety, keep both hands on the spray wand at all times. .Pull back and hold the trigger to operate the pressure washer. .Release the trigger to stop the flow of water through the nozzle. To engage the lock out: .Push up on the lock out until it clicks into the slot. To disengage the lock out: .Push the lock out down and into its original position. For the most effective cleaning, the spray nozzle should be between 8 in. and 24 in. from the surface to be cleaned. If the spray is too close it can damage the cleaning surface. SELECTING THE RIGHT QUICK-CONNECT NOZZLE FOR THE JOB See Figure 12 - 13. ............Before starting any cleaning job, determine the best nozzle for the job. Each of the three nozzles has a different spray NOZZLE “CLICK” SLOT LOCK OUT pattern. The nozzle patterns are: detergent (low pressure), 25. (medium pressure), and 0. (high pressure). NOTE: For a gentle rinse, select the detergent nozzle. Scouring the surface requires a more direct spray of water. Select the 0. nozzle for tough jobs. ..Apply detergent using the detergent nozzle. ..CAUTION: NEVER change nozzles without locking the lock out on the spray wand. Usi...
Эта инструкция также подходит к моделям:Моечное оборудование - HU80522 (4.69 mb)