Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
PRESSURE WASHER OPERATING FEATURES PRESSURE ADJUSTMENTS The pressure setting is preset at the factory to achieve op ti mum pres sure and cleaning. If you need to lower the pres sure, it can be accomplished by these meth ods. 1. Back away from the sur face to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned. 2. Change to the 40. nozzle - (white) this nozzle delivers a less powerful stream of water and a wider spray pattern. DO NOT attempt to increase pump pressure. A higher pressure setting than the factory set pressure may damage pump. SPRAY WAND NOZZLES The nozzles for the spray wand are stored in the nozzle holder on the panel assembly. Colors on the panel identify nozzle location and spray pattern. Refer to the following chart to choose the correct nozzle for the job to be performed. CHANGING NOZZLES ON SPRAY WAND Risk of fluid injection. Do not direct discharge stream toward persons, unprotected skin, eyes or any pets or animals. Serious injury will occur. Flying objects could cause risk of serious injury. Do not attempt to change nozzles while pressure washer is running. Turn engine off before changing nozzles. 1. Pull quick- connect coupler back and insert nozzle. 2. Release quick- connect coupler and twist nozzle to make sure it is secure in coupler. Flying object could cause risk of serious injury. Ensure nozzle is completely inserted in quick-connect socket and quick-connect snap ring is fully engaged (forward) before squeezing gun trigger. A16064 10- ENG Nozzle Color Red Yellow Green White Black Spray Pattern 0. 15. 25. 40. low pressure Uses powerful pinpoint for very intense cleaning intense cleaning of small areas intense cleaning of larger areas covers wide areas of cleaning applies cleaning solutions Surfaces * Metal or concrete DO NOT use on wood metal, concrete, or wood metal, concrete, or wood metal, concrete, wood, or vinyl metal, concrete, wood, or vinyl * The high pressure spray from your pressure washer is capable of causing damage to surfaces such as wood, glass, automobile paint, auto striping and trim, and delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of the spray. HOW TO APPLY CHEMICALS/CLEANING SOLVENTS Applying chemicals or cleaning solvents is a low pressure operation. NOTE: Use only soaps and chemicals designed for pressure washer use. Do not use bleach. To Apply chemicals: 1. Press chemical hose onto barbed fi tting located near high pressure hose connection of pump as shown. Barbed Fitting 2. Place other end of chemical hose with filter on it into container holding chemical/cleaning solution. NOTE: For every 7 gallons (26.5 liters) of water pumped 1 gallon (3.8 liters) of chemical/cleaning solution will be used. 3. Install low pressure (black) nozzle into quick connect fi tting of spray wand, see How To Use Spray Wand paragraph in this section. 4. After use of chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. If chemicals remain in the pump it could be damaged. Pumps damaged due to chemicals will not be covered under warranty. NOTE: Chemicals and soaps will not siphon when spray wand is in the high pressure setting. 11 - ENG A16064 To reduce the risk of injury, read the pressure washer instruction manual and the engine instruction manual before starting pressure washer. Risk of fluid injection and laceration. When using the high- pressure setting, DO NOT allow the high-pressure spray to come in contact with unprotected skin, eyes, or with any pets or animals. Serious injury will occur. • Your washer operates at fl uid pressures and velocities high enough to penetrate human and animal fl esh, which could result in amputation or other serious injury. Leaks caused by loose fi ttings or worn or damaged hoses can result in injection injuries. DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a physician immediately! Risk of Fire, Asphyxiation and Burn. NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank. • NEVER fi ll fuel tank completely. Fill tank to 1/2" (12.7 mm) below bottom of fi ller neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine. • NEVER run engine in doors or in en closed, poorly ven ti lat ed areas. En gine exhaust con tains carbon mon ox ide, an odorless and deadly gas. • DO NOT let hoses come in contact with very hot engine muffl er during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty. Risk of property damage. NEVER pull water supply hose to move pres sure washer. This could damage hose and/or pump inlet. • DO NOT use hot water, use cold water only. • NEVER turn water supply off while pressure washer engine is running or d...
Эта инструкция также подходит к моделям:Моечное оборудование - DVH2600 (1.87 mb)