Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Refer to the machine data plate (Fig. 3) and Electrical Data, below. ELECTRICAL DATA Model Volts / Hertz / Phase Receptacle, Circuit and Plug Size Receptacle and Plug Type Reference 4346 200 / 60 / 3 30 Amps Receptacle Shown G YW Z X NEMA L21-30RReceptacle: L21-30PPlug: 230 / 60 / 3 30 Amps Receptacle Shown G Y Z X NEMA L15-30RReceptacle: L15-30PPlug: 460 / 60 / 3 20 Amps Receptacle Shown G Z Y X NEMA L16-20RReceptacle: L16-20PPlug: Compiled in accordance with the National Electrical Code, ANSI / NFPA 70, 1993 Edition. CHECK MOTOR ROTATION With the grinder attachment in place and the hopper guard closed, check worm rotation before making a permanent electrical connection by first pushing the MIX-GRIND switch and then pushing the STOP switch (Fig. 2). If there is no worm rotation but the mixer arm turns, correct the rotation using the following procedure: DISCONNECT THE ELECTRICAL POWER SUPPLY and interchange any two of the incoming power supply leads. Reconnect the power supply and push the MIX-GRIND switch to verify that both the worm and the mixer arm rotate. CONTROL BOX HEATER The Mixer-Grinder has a heater in the control box to keep the controls dry. It is automatically ON when the machine is electrically connected. The Mixer-Grinder should always be connected EXCEPT when performing assembly, disassembly, cleaning, or maintenance of the machine. After cleaning, reconnect the electrical power supply. – 4 – INSTALLATION DIAGRAM – 5 – OPERATION CONTROLS (Fig. 2) Fig. 2 STOP c STOP START MIX MIX-GRIND FOOT SWITCH ACTIVATOR ON OFF c START BUTTONS MIX — Starts rotating the mix arm. Use the Stop Button to stop mixing. MIX-GRIND — Starts rotating both mix arm and worm. Use the Stop Button to stop mixing and grinding. STOP BUTTON — Turns the mixer-grinder off. FOOT SWITCH ACTIVATOR ON-OFF — When in the On position, the Mix and Mix-Grind Start Buttons are inoperable and the accessory Foot Switch can be used to Mix-Grind ONLY. The indicator light shows when the Foot Switch is On. HOPPER GUARD INTERLOCK — The mixer-grinder has a magnetic actuated interlock in the hopper. The hopper guard (lid) must be closed before the machine can operate. Raising the hopper guard opens the electrical circuit and makes the machine inoperative. SPANNER WRENCH THUMB SCREW BUSHING RETAINER GRINDER ATTACHMENT ADJUSTING RING MIXING ARM SEAL MACHINE DATA PLATE WORM PL-52465 Fig. 3 – 6 – GRINDER ATTACHMENT The grinder attachment can easily be removed for cleaning (see Cleaning, page 8). Use the spanner wrench to loosen the adjusting ring and remove the adjusting ring, plate, knife, and worm (Fig. 3). Next loosen, but do not remove the two flange nuts, using the spanner wrench. Rotate the cylinder clockwise and remove the cylinder. At reassembly, make sure the cylinder's flange nuts are tight before assembling the worm and adjusting ring. Use only the flange nuts provided. A heavy duty tapered roller bearing, which is lubricated by transmission oil, takes the worm thrust. A rubber seal at the drive end of the worm prevents loss of lubricant or entrance of moisture. Before using the grinder attachment, take it apart and thoroughly wash it. The knife and plate need some preliminary lubrication: Rub tallow or food grade mineral oil over the cutting faces of these parts. When assembling the knife, be sure to turn the cutting side towards the perforated plate. The notch on the circumference of the plate must fit over the pin in the cylinder. Knives and plates must be sharp and true for proper cutting action. Keep the grinder attachment in a clean and sanitary condition. MIXING ARM Loosen the thumb screw and rotate the bushing retainer (Fig. 3). Raise the hopper guard, pull the mixing arm from the drive slot, and lift the mixing arm from the hopper. MIXING AND GRINDING The model 4346 has a normal capacity of 200 pounds when using 80% fresh and 20% frozen chips; 215 pounds using 100% trimmings; or a maximum of 240 pounds of second grind through a 1/8" plate. Second cut meat may be mixed in the hopper for any desired length of time. During the MIX operation, the mixing arm rotates in reverse direction from MIX-GRIND operation and the grinder worm does not rotate. Continuous mixing occurs along with grinding in the MIX-GRIND operation. Mixing of uncut or unground meat is not recommended. Grinding Procedure First Grind . . . Fill the hopper and close the hopper guard. Overfilling will bend the hopper guard and may cause the interlock to open the electrical circuit. Push the MIX-GRIND Button to start grinding. Press the STOP Button to stop grinding. Second Grind . . . Fill the hopper and close the hopper guard. Press the MIX Button. After desired mixing, press the STOP Button. Then, press the MIX-GRIND Button to start grinding; press the STOP Button to stop grinding; or activate and use the optional accessory Foot Switch. – 7 – CLEANING WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY BEFORE CLEANING OR SERVICING THIS MACHINE. In any cleaning operatio...