Оценок - 6, средний балл: 4
(
)
)
|
Фрагмент инструкции
2000) MODEL A200 MIXER – 2 – Installation, Operation, and Care of A200 MIXER SAVE THESE INSTRUCTIONS GENERAL The model A200 mixer is a 20 quart, bench-type mixer with a 1/2 H.P. motor, and a #12 attachment hub. With the use of special agitators, a 12 quart bowl may be used on the A200 mixers. The floor model and the deluxe finish model are equipped with a timer. Most A200 mixers are equipped with a 0 - 15 minute timer. There are a variety of attachments and accessories available for all models, and these are explained in a separate Use and Applications Handbookwhich is supplied with each mixer. INSTALLATION UNPACKING Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate. LOCATION Place the mixer on a suitable sturdy level surface. There should be adequate space around the mixer for the user to operate the controls and install and remove bowls. Holes are provided in the base to permanently secure the mixer, although this is not necessary in normal installations. Four plastic plugs are supplied with the mixer to plug these holes if they are not used. ELECTRICAL CONNECTIONS (Cord Connected Mixers) WARNING: THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A THREE-PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG. – 3 – OPERATION WARNING: MOVING BEATER IN BOWL. KEEP HANDS, CLOTHING, AND UTENSILS OUT WHILE IN OPERATION, DO NOT USE WITHOUT INTERLOCKED GUARD. CONTROLS All models are furnished with an On-Off toggle switch which controls power to the mixer. The Bowl Guard must be in position or the mixer will not operate. Refer to page 6. If the Bowl Support is not all the way up, the mixer will not operate unless the On-Off switch is held in the up position. The TIMER (if equipped) is used in conjunction with the On-Off switch for timed mixing operations and will stop the mixer when the desired time has elapsed. With the timer set on HOLD, the mixer will run until the On-Off switch is turned to Off. The GEAR SHIFT LEVER (Fig. 1) is used to change speeds. Always stop the mixer before changing speeds. To change speeds, turn the switch Off, move the gear shift lever to the desired speed, and turn the switch back On. Speed 1 (Low) — This speed is for heavy mixtures such as bread dough, heavy batters, and potatoes. Speed 2 (Medium) —This speed is for light dough which must rise quickly, cake batters, and some whipping operations. Speed 3 (High) — This is a fast speed for light work such as whipping cream, beating eggs, and mixing thin batters. The BOWL LIFT HANDLE (Fig. 1) is used to raise and lower the bowl. To raise the bowl, rotate the handle upward; rotating the handle downward lowers the bowl. MIXING This section explains operation of the mixer and how to install bowls, agitators, and attachments. A separate Use and Applications Handbook is provided with the mixer which contains information on mixing procedures and outlines specific uses for agitators, attachments, and accessories. Bowl New mixer bowls and agitators (beaters, whips, and dough arms) should be thoroughly washed with hot water and a mild soap solution, rinsed with either a mild soda or vinegar solution, and thoroughly rinsed with clear water BEFORE being put into service. This cleaning procedure should also be followed for bowls and agitators before whipping egg whites or whole eggs. The bowl must be installed before the agitator. To install the bowl, fully lower the bowl support (Fig. 1). Position the bowl so the alignment bracket on the back of the bowl is in the bowl retainer and the alignment pins (Fig. 1) on the front of the bowl support fit in the holes on the sides of the bowl. Lock the bowl in place by rotating the bowl clamps (Fig. 1) over the ears of the bowl. Agitator To install an agitator (Fig. 1), the bowl must be installed and fully lowered. Place the agitator in the bowl, push it up on the agitator shaft, and turn it clockwise to seat the shaft pin in the slot of the agitator shank. – 4 – A200 A200 WITH TIMER 56 ON ON 10 OFF 11 OFF 1 2 3 4 7 8 9 12 13 1415 ATTACHMENT HUB THUMB SCREW GEAR SHIFT LEVER WIRE CAGE AGITATOR BOWL CLAMP ALIGNMENT PIN CONTROL PANEL BOWL LIFT HANDLE SPLASH GUARD APRON BOWL SUPPORT BOWL LIFT SLIDEWAYS PL-53477 Fig. 1 To Raise the Bowl While Mixing To raise the bowl while the agitator is mixing the product (when required by recipe or when using the Bowl Scraper Attachment): Load ingredients. Close Wire Cage Assembly. Select Low speed. To begin mixing, hold the On-Off switch in the up position; then raise the bowl. Attachments To install an attachment, loosen the thumb screw on the...