Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
PARTS LISTS AND POWER OPTIONS Drum and Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15 Mixing Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17 Engine Housing Assembly . . . . . . . . . . . . . . . . . . . . . . . . .18-19 Frame Drive and Clutch Control . . . . . . . . . . . . . . . . . . . . 20-21 Engine and Power Options . . . . . . . . . . . . . . . . . . . . . . . . .22-25 2 1 – SAFETY PRECAUTIONS THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND PRACTICE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND HAVE BEEN PROPERLY INSTRUCTED. Read all operating and maintenance instruction before operating or servicing the mixer. Test run the empty unit prior to actual use. A mixer is only as safe as its operator. Give complete and undivided attention to the operations of the mixer. Know how to stop the mixer and engine/motor instantly in emergency situations. Always keep all guard and safety devices and labels attached and in place before operating mixer. Close engine housing during mixer operation. Keep inexperienced and unauthorized people away from the mixer at all times. Never leave the mixer unattended when it is running Shut off engine or disconnect electric power before making repairs or adjustments. NEVER REACH INTO DRUM OR PLACE TOOLS INTO THE DRUM WHILE THE MIXER IS RUNNING. Do not overfill- -do not attempt to exceed the mixer’s rated capacity. Do not refuel the engine when it is hot or running. Do not smoke while refueling the engine. Block mixer wheels when in operation. Keep the mixer well maintained and in good operating condition. Check periodically for loose or missing hardware. Avoid loose clothing that could get caught in moving parts or on control levers. KEEP HANDS AND FEET AWAY FROM MOVING PARTS. 3 Never charge or fill the unit prior to starting the mixing blades as an overload encountered in starting a loaded unit could damage the engine/motor or drive components. Connect safety chains as instructed when towing the mixer. Connect only to correct hitch or coupler. Keep warning, caution and safety instruction labels clean and in good condition. Replace missing, damaged or illegible labels. 2 – ASSEMBLY AND PRO-OPERATIONAL CHECKS The only assembly required on this mixer is the installation of the drum tilt handle. Remove the handle from the bag shipped in the drum and install, referring to parts list Figure 5, item numbers 7, 18, 20 and 21 for proper assembly. The following steps should be taken prior to placing the mixer in use: 1. The operator must be familiar with the location and operation of all controls. 2. Check the crankcase oil level on gasoline powered units, and fill the fuel tank before starting. 3. Check for free rotation of the mixer blade shaft by rotating the drum through one complete dump-charge-dump cycle. Make sure no foreign objects or tools are in drum before starting engine/motor. 4. Start engine/motor, slowly engage the drum drive and check for smooth operation of the mixer blade shaft and drive. 5. Move the clutch lever through several cycles to assure correct clutch operation. 4 3 – CONTROLS AND OPERATIONS 1. The mixing paddles feature adjustable rubber wipers and steel backing plates. Paddles are factory preset for appropriate drum wrap clearance. If adjustment is required, proceed as follows: A. Loosen the wiper attaching hardware and move the wiper outward to maintain contact with the drum but without folding over when in operation. B. After adjustment, turn the mixer arms one full turn manually to check clearance and eliminate the possibility of wiper back plates contacting the drum. 2. Read through the manual for all operation, adjustment and maintenance instructions. Be sure all engine/motor and drive system operation instructions are followed as outlines. 3. All nuts and cap screws should be checked and tightened during the first two (2) hours of use. Periodic checks should be made thereafter. CLUTCH CONTROL LEVER This control is located in front of the mixing drum on the mixer leg. SEE FIGURE 1. This control engages and disengages the drive to the mixing blades. TO ENGAGE: Position lever in line with the mixer frame (12 o’clock position). Lever is held in the engage position by the over-center action of the linkage. TO DISENGAGE: Push lever down (counter-clock-wise) to the 9 o’clock position. Lever is spring loaded to hold it in the disengaged position. 5 TOW POLE ASSEMBLY The tow pole assembly is located on the front of the mixer and is used for transport only. For transport, pull the tow pole assembly out, line up the hold and insert the L-shaped pin through holes. When operating the mixer, pull the L-shaped pin out of the hole and push tow pole assembly all ...
Эта инструкция также подходит к моделям:Миксеры - MORTAR-PLASTER 600MP (387.74 kb)