Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
33/4" (95mm) English 10 English 11 Removing Packaging • Cut foil wrap in the area of corner posts. • Remove foil completely. • Remove top cardboard. • Remove all top and side cardboard and Styrofoam braces. • Place oven in front of cabinets where it is to be installed. • Unscrew unit from Left and Right Brackets as show in “Left and Right Packaging Bracket Removal.” Left and Right Packaging Bracket Removal Note: Bracket remains in packaging base. Unit should stay in packaging base plate until ready to be lifted into cabinet cutout. For Convection Microwave Combination Units Remove 2 rear support Convection Microwave Shipping Brackets prior to installation as shown in “Convection Microwave Shipping Bracket Removal.” Convection Microwave Shipping Bracket Removal (for Convection Microwave Combination Units Only) Preparing Oven Place oven in front of cabinets where it is to be installed. Rest it on a jack or other sturdy support so that it is in line with the cabinet cutout. Installation Electrical Installation All model ovens on the front cover are dual rated, designed to be connected to either 208/240V AC, 60 Hz, 4 wire, single-phase power supply. Model Circuit Required 208V, 60 Hz 240V, 60 Hz HBN33, HBL33 25 AMP 30 AMP HBN34, HBL34, HBN54, HBL54 HBL85 30 AMP 30 AMP HBN35, HBL35, HBN56, HBL56, HBL57, HBL8650, HBL8750 40 or 50 Amp circuit. Refer to local electrical codes for de-rating requirements. The electrical supply should be a 4-wire single-phase AC. Install a suitable conduit box (not furnished). Important: Local Codes may vary, installation, electrical connections and grounding must comply with all applicable local codes. If local codes permit grounding through the electrical supply neutral, connect both the white neutral wire and the bare ground wire from the oven to the white neutral electrical supply wire. English 12 Electrical Connection The four-wire connection is preferred, but where local codes permit, the three wire connection is also acceptable. Four-wire Connection • Connect the red oven wire to the red electrical supply wire (hot wire). • Connect the black oven wire to the black electrical supply wire (hot wire). • Connect the white neutral oven wire to the white neutral (not bare ground) electrical supply wire. • Connect the bare ground oven wire to the bare ground electrical supply wire. Three-wire Connection • Connect red wire from oven to red wire injunction box. • Connect black wire from oven to black wire in junction box. • Connect both green ground wire and white wire from oven to white (or gray) neutral wire in junction box. The conduit cable, where connected at the oven, swivels. Rotate conduit cable upward (or downward) and direct through hole prepared in cabinet to attach to J- Box. To maintain serviceability, the flex conduit must not be shortened and should be routed to permit temporary removal of the oven. English 13 Oven Installation Note: Before installing the oven be sure to verify the cabinet dimensions and electrical connections. Removing the Oven Door For ease of installation, some oven doors may be removed to reduce the weight of the oven by 30 lbs (14 kg) per door, before installing into the cabinet. See “To remove the oven door.” CAUTION: m When removing the door: • Make sure oven is cool and power to the oven has been turned off before removing the door. Failure to do so could result in electrical shock or burns. • The oven door is heavy and fragile. Use both hands to remove the oven door. The door front is glass. Handle carefully to avoid breaking. • Grasp only the sides of the oven door. Do not grasp the handle as it may swing in your hand and cause damage or injury. • Failure to grasp the oven door firmly and pr...
Эта инструкция также подходит к моделям:Микроволновые печи - BL54 (2.34 mb)
Микроволновые печи - HBL8750 (2.34 mb)
Микроволновые печи - HBN33 (2.34 mb)
Микроволновые печи - HBL33 (2.34 mb)