Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
3 x audio jacks (Line In, Line Out, Mic In) I/O Controller ..iTE® I/O Controller Chip Hardware Monitor ..System voltage detection ..CPU/System temperature detection ..CPU/System fan speed detection ..System fan speed control * Whether the fan speed control function is supported will depend on the cooler you install. BIOS ..2 x 32 Mbit flash ..Use of licensed AMI EFI BIOS ..Support for DualBIOS™ ..PnP 1.0a, DMI 2.0, SM BIOS 2.6, ACPI 2.0a Unique Features ..Support for @BIOS ..Support for Q-Flash ..Support for Xpress Install ..Support for EasyTune * Available functions in EasyTune may differ by motherboard model. ..Support for Smart Recovery 2 ..Support for Auto Green ..Support for ON/OFF Charge Bundled Software ..Norton® Internet Security (OEM version) ..Intel® Smart Connect Technology Operating System ..Support for Windows 8.1/8/7/XP Form Factor ..Mini-ITX Form Factor; 17.0cm x 17.0cm * GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice. * Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns. 1-3 Installing the Memory Read the following guidelines before you begin to install the memory: ••Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest supported memory speeds and memory modules.) ••Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. ••Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction. 1-4 Back Panel Connectors PS/2 Keyboard/Mouse Port Use the upper port (green) to connect a PS/2 mouse and the lower port (purple) to connect a PS/2 keyboard. Parallel Port Use the parallel port to connect devices such as a printer, scanner and etc. The parallel port is also called a printer port. Serial Port Use the serial port to connect devices such as a mouse, modem or other peripherals. D-Sub Port The D-Sub port supports a 15-pin D-Sub connector. Connect a monitor that supports D-Sub connection to this port. USB 2.0/1.1 Port The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc. HDMI Port The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 1920x1200, but the actual resolutions supported are dependent on the monitor being used. After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The item name may differ from operating system.) Dual Display Configurations for the Onboard Graphics: Dual-display configurations are supported in operating system environment only, but not during the BIOS Setup or POST process. RJ-45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs. Connection/ Speed LED Connection/Speed LED: State Description Orange 1 Gbps data rate Green 100 Mbps data rate Off 10 Mbps data rate Activity LED: State Description Blinking Data transmission or receiving is occurring Off No data transmission or receiving is occurring Activity LED LAN Port Line In Jack (Blue) The line out jack. Use this audio jack for line in devices such as an optical drive, walkman, etc. Line Out Jack (Green) The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration. Mic In Jack (Pink) The default Mic in jack. Microphones must be connected to this jack. To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver. ••When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard. ••When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector. 1-5 Internal Connectors 4 3 1 5 14 2 13 9 11 8 7 10 12 7 6 1) ATX_12V 2) ATX 3) CPU_FAN 4) SYS_FAN 5) IDE 6) SATA3 0 7) SATA2 1/2/3 8) F_PANEL 9) F_AUDIO 10) F_USB1/F_USB2 11) SPDIF_O 12) BAT 13) CLR_CMOS 14) CI Read the following guidelines before connecting external devices: ••First make sure your devices are compliant with the connectors you wish to connect. ••Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to...