Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Gigabyte, модель GA-M68MT-D3

Производитель: Gigabyte
Размер: 8.23 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


CAS# latency Options are: Auto (default), 4T~12T. RAS to CAS R/W Delay Options are: Auto (default), 5T~12T. Row Precharge Time Options are: Auto (default), 5T~12T. Minimum RAS Active Time Options are: Auto (default), 15T~30T. 1T/2T Command Timing Options are: Auto (default), 1T, 2T. TwTr Command Delay Options are: Auto (default), 4T~7T. Trfc0 for DIMM1 Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Trfc1 for DIMM3 Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Write Recovery Time Options are: Auto (default), 5T~12T. Precharge Time Options are: Auto (default), 4T~7T. Row Cycle Time Options are: Auto (default), 11T~42T. RAS to RAS Delay Options are: Auto (default), 4T~7T. CKE Power Down Mode Determines whether to set the memory to power down mode when the CKE pin is closed. (Default: Disabled) CKE Power Down Control Allows you to select a CKE power down mode. Options are per Channel (Default), per CS. CPU NB VID Control Allows you to set the CPU Northbridge VID voltage. Auto sets the CPU Northbridge VID voltage as required. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. CPU Voltage Control Allows you to set the CPU voltage. Auto sets the CPU voltage as required. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. DDR3 Voltage Control Allows you to set the memory voltage. Normal Supplies the memory voltage as required. (Default) -0.05V ~ +0.4V The adjustable range is from -0.05V to +0.4V. Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory. Normal CPU Vcore Displays the normal operating voltage of your CPU. 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2010 Award Software Standard CMOS Features Item Help Menu Level . Date (mm:dd:yy) Fri, May 14 2010 Time (hh:mm:ss) 22:31:24 } IDE Channel 0 Master [None] } IDE Channel 0 Slave [None] } IDE Channel 2 Master [None] } IDE Channel 3 Master [None] } IDE Channel 4 Master [None] } IDE Channel 5 Master [None] Drive A [1.44M, 3.5"] Floppy 3 Mode Support [Disabled] Halt On [All, But Keyboard] Base Memory 640K Extended Memory 1918M ....: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Date (mm:dd:yy) Sets the system date. Time (hh:mm:ss) Sets the system time. IDE Channel 0 Master/Slave, IDE Channel 2, 3, 4, 5 Master IDE HDD Auto-Detection, IDE Auto-Detection Press to autodetect the parameters of the IDE/SATA device on this channel. IDE Channel 0 Master/Slave, Extended IDE Drive Configure your IDE/SATA devices by using one of the three methods below: • Auto Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default) • None If no IDE/SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. Access Mode Sets the hard drive access mode. (Default: Auto) The following fields display your hard drive specifications. If you wish to enter the parameters manually, refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Cylinder Number of cylinders. Head Number of heads. Precomp Write precompensation cylinder. Landing Zone Landing zone. Sector Number of sectors. Drive A Allows you to select the type of floppy disk drive installed in your system. If you do not install a floppy disk drive, set this item to None. Options are: None, 360K/5.25", 1.2M/5.25", 720K/3.5", 1.44M/3.5", 2.88M/3.5". Floppy 3 Mode Support Allows you to specify whether the installed floppy disk drive is 3-mode floppy disk drive, a Japanese standard floppy disk drive. Options are: Disabled (default), Drive A. Halt On Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors," "No Errors," "All, But Keyboard" (default), "All, But Diskette," "All, But Disk/Key." Memory These fields are read-only and are determined by the BIOS POST. 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2010 Award Software Advanced BIOS Features Item Help Menu Level . AMD C1E Support (Note) [Disabled] Virtualization [Enabled] AMD K8 Cool&Quiet control [Auto] CPU Unlock (Note) [Disabled] CPU core Control [Auto] x CPU core 2 (Note) Enabled x CPU core 3 (Note) Enabled } Hard Disk Boot Priority [Press Enter] First Boot Device [Floppy] Second Boot Device [Hard Disk] Third Boot Device [CDROM] Password Check [Setup] HDD S.M.A.R.T. Capability [Disabled] Away Mode [Disabled] Backup BIOS Image to HDD [Disabled] Init Display First [PEG] Frame Buffer Size [Auto] Onboard GPU [Enable If No Ext PEG] ....: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5:...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории