It allows you to limit access to the system. · IDE HDD auto detection Automatically configure hard disk parameters. · Save & Exit Setup Save CMOS value settings to CMOS and exit setup. · Exit Without Saving Abandon all CMOS value changes and exit setup. 44 BIOS Setup · Time The times format in . The time is calculated base on the 24-hour military -time clock. For example, 1 p.m. is 13:00:00. · IDE Primary Master, Slave / Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installe d in the computer. There are two types: auto type, and user definable type. User type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If you select User Type, related information will be asked to enter to the following items. Enter the information directly from the keyboard and press . Such information should be provided in the documentation form your hard disk vendor or the system manufacturer. CYLS. Number of cylinders HEADS number of heads PRECOMP write precomp LANDZONE Landing zone SECTORS number of sectors If a hard disk has not been installed select NONE and press . · Drive A type / Drive B type The category identifies the types of floppy disk drive A or drive B that has been installed in the computer. None No floppy drive installed 360K, 5.25 in. 5.25 inch PC-type standard drive; 360K byte capacity. 1.2M, 5.25 in. 5.25 inch AT -type high-density drive; 1.2M byte capacity (3.5 inch when 3 Mode is Enabled). 720K, 3.5 in. 3.5 inch double-sided drive; 720K byte capacity 1.44M, 3.5 in. 3.5 inch double-sided drive; 1.44M byte capacity. 2.88M, 3.5 in. 3.5 inch double-sided drive; 2.88M byte capacity. 46 BIOS Setup BIOS Features Setup AMIBIOS SETUP – BIOS FEATURES CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved 1st Boot Device :Floppy 2nd Boot Device :IDE-0 3rd Boot Device :CDROM S.M.A.R.T for Hard Disks :Disabled BootUp Num-Lock :On Floppy Drive Seek :Disabled Password Check :Setup Processor Serial Number :Disabled ESC : Quit .¬®: Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift)F2 :Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Figure 3: BIOS Features Setup · 1st / 2nd / 3rd Boot Device The default value is Floppy or LS -120 / ZIP A: or ATAPI ZIP C: or CDROM or SCSI or NET WORK / I20 or IDE -0~IDE -3 or Disabled. Floppy Boot Device by Floppy. LS -120 / ZIP A: Boot Device by LS -120 / ZIP A:. CDROM Boot Device by CDROM. SCSI Boot Device by SCSI. NETWORK Boot Device by NETWORK. IDE -0~IDE -3 Boot Device by IDE -0~IDE -3. Disabled Boot Device by Disabled. ATAPI ZIP C: Boot Device by ATAPI ZIP C:. 48 BIOS Setup Chipset Features Setup AMIBIOS SETUP –CHIPSET FEATURE CMOS SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved *** DRAM Timing *** Top Performance :Disabled SDRAM Timing by SPD :Disabled SDRAM CAS# Latency :3 DRAM Frequency :Auto C2P Concurrency & Master :Enabled DRAM Integrity Mode :Disabled AGP Mode :4X AGP Comp. Driving :Auto Manual AGP Comp. Driving :CB AGP Aperture Size :64MB ClKGen Spread Spectrum :Center ± 0.25% USB Controller :All USB Port USB Legacy Support :Disabled ESC : Quit .¬®: Select Item F1 : Help PU/PD/+/- : Modify F5 : Old Values (Shift)F2 :Color F6 : Load BIOS Defaults F7 : Load Setup Defaults Figure 4: Chipset Features Setup · Top Performance If you wish to maximize the performance of your system, set “Top Performance” as “Enabled”. Disabled Set Top Performance is disabled. (Default Value) Enabled Set Top Performance is enabled. · SDRAM Timing by SPD Disabled SDRAM Timing by SPD Function Disabled. (Default Value) Enabled SDRAM Timing by SPD Function Enabled. · SDRAM CAS# Latency 3 For Slower SDRAM DIMM module. (Default Value) 2 For Fastest SDRAM DIMM module. · DRAM Frequency Auto Set DRAM Frequency automation. (Default Value) 100MHz Set DRAM Frequency is 100MHz. 66MHz Set DRAM Frequency is 66MHz. 133MHz Set DRAM Frequency is 133MHz. 50 BIOS Setup · USB Controller All USB Port Set USB Controller Function used all USB Port. (Default Value) USB Port 0&1 Set USB Controller Function used USB Port 0&1. USB Port 2&3 Set USB Controller Function used USB Port 2&3. Disabled USB Controller Function Disabled. · USB Legacy Support Keyboard Set USB Legacy Support Keyboard. Keyb+Mouse Set USB Legacy Support Keyboard +Mouse. Disabled Disabled USB Legacy Support Function. (Default Value) 52 BIOS Setup 54 · Suspend Time Out (Minute.) Disabled Disabled Suspend Time Out Function. (Default Value) 1 Enabled Suspend Time Out after 1min. 2 Enabled Suspend Time Out after 2min. 4 Enabled Suspend Time Out after 4min. 8 Enabled Suspend Time Out after 8min. 10 Enabled Suspend Time Out after 10min. 20 Enabled Suspend Time Out after 20min. 30 Enabled Suspend Time Out after 30min. 40 Enabled Suspend Time Out af...
