Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Материнские платы - GA-6RXB (3.14 mb)
Материнские платы - GA-6RXB (3.03 mb)
Фрагмент инструкции
Enabled Pentium® !!! Processor Serial Number Feature. Disabled Disable this function. (Default value) • BIOS Flash Protection Enabled Enable BIOS Flash Protection. This will prevent BIOS Flash write after POST. Disabled To flash/upgrade BIOS on this MB, this item must be disable. We recommend this item to be set to “Disabled”. (Default Value) 95 BIOS Setup Chipset Features Setup We would not suggest you change the chipset default setting unless you really need it. AMIBIOS SETUP – CHIPSET FEATURES SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved ***DRAM Timing*** Top Performance : Disabled DRAM Timing by SPD : Enabled DRAM Frequency : 133MHz DRAM CAS# Latency : 2.5 Cycles DRAM Bank Interleave : 4-WAY ..DRAM Command Rate : 2T Command AGP Mode : 4X AGP Read Synchronization : Enabled AGP Fast Write : Disabled AGP Comp. Driving : Auto Manual AGP Comp. Driving : CB AGP Aperture Size : 64MB PCI Delay Transaction : Enabled USB Controller : All USB Port USB Legacy Support : Disabled ESC : Quit ^v> <: Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values (Shift)F2:Color F6 : Load BIOS Defaults F7 : Load SETUP Defaults Figure 4: Chipset Features Setup ..This item will only be shown when using DDR memory. • •••• Top Performance If you wish to maximize the performance of your system, set “Top Performance” as “Enabled”. Disabled Disable this function. (Default Value) Enabled Top Performance Enable. • •••• DRAM Timing by SPD Enabled Enable DRAM Timing by SPD. Enable this function, the bios will set DRAM Frequency/DRAM CAS#/DRAM Bank Interleave according to the SPD Data in DRAM. (Default Value) Disabled Disable DRAM Timing by SPD. • •••• DRAM Frequency 100MHz Set DRAM Frequency to 100MHz. 133MHz Set DRAM Frequency to 133MHz. 96 6RXB Motherboard 97 • DRAM CAS# Latency DDR: 2 Cycles Set DRAM CAS# Latency to 2 Cycles. 2.5 Cycles Set DRAM CAS# Latency to 2.5 Cycles. SDRAM: 2 Cycles Set DRAM CAS# Latency to 2 Cycles. 3 Cycles Set DRAM CAS# Latency to 3 Cycles. • DRAM Bank Interleave 4-WAY Set DRAM Bank Interleave to 4-WAY. 2-WAY Set DRAM Bank Interleave to 2-WAY. Disabled Disable this function. • DRAM Command Rate 2T Command Set DRAM Command Rate to 2T Command. (Default Value) 1T Command Set DRAM Command Rate to 1T Command. • AGP Mode 4X Set AGP Mode to 4X (Only if the AGP Card support 4X Rate). (Default Value) 1X Set AGP Mode to 1X. 2X Set AGP Mode to 2X. • AGP Read Synchronization Enabled Enable AGP Read Synchronization. (Default Value) Disabled Disable AGP Read Synchronization. • AGP Fast Write Enabled Enable this function only if the AGP Card support Fast Write Function. (Enable this function can increase AGP performance). Disabled Disable this function. (Default Value) • AGP Comp. Driving Auto Set AGP Comp. Driving to Auto. (Default Value) Manual Set AGP Comp. Driving to Manual. BIOS Setup 98 If AGP Comp. Driving is Manual. Manual AGP Comp. Driving: 00~FF • AGP Aperture Size 4 MB Display AGP Aperture Size is 4MB. 8 MB Display AGP Aperture Size is 8MB. 16 MB Display AGP Aperture Size is 16MB. 32 MB Display AGP Aperture Size is 32MB. 64 MB Display AGP Aperture Size is 64MB. (Default Value) 128 MB Display AGP Aperture Size is 128MB. 256 MB Display AGP Aperture Size is 256MB. • PCI Delay Transaction Enabled Enable Delay Transaction. (Default Value) Disabled Disable Delay Transaction. • USB Controller All USB Port Enable All USB Ports 0,1,2,3,4,5. (Default Value) Disabled Disable USB Controller. Port 0&1 Enable USB Ports 0&1. Port 2&3 Enable USB Ports 2&3. Port 0&1, 2&3 Enable USB Ports 0&1, 2&3. Port 4&5 Enable USB Ports 4&5. Port 0&1, 4&5 Enable USB Ports 0&1, 4&5. Port 2&3, 4&5 Set USB Controller to Port 2&3, 4&5. • USB Legacy Support Keyboard/FDD Enable USB Legacy Support for USB Keyboard & USB Floppy. KB/Mouse/FDD Enable USB Legacy Support for USB Keyboard/USB Mouse & USB Floppy. Disabled Disable USB Legacy Support Function. (Default Value) 6RXB Motherboard Power Management Setup AMIBIOS SETUP – POWER MANAGEMENT SETUP ( C ) 1999 American Megatrends, Inc. All Rights Reserved ACPI Standby State : S1/POS USB Dev Wakeup From S3~S5 : Disabled IRQ3 : Monitor IRQ4 : Monitor IRQ5 : Ignore IRQ7 : Monitor IRQ9 : Ignore IRQ10 : Ignore IRQ11 : Ignore IRQ13 : Ignore IRQ14 : Monitor IRQ15 : Ignore Soft-Off by Power Button : Instant Off AC Back Function : Off Modem Ring On/Wake On Lan : Enabled PME Event Wake Up : Enabled Keyboard Wakeup From : S1(Suspend) PS/2 Mouse Wakeup From : S1(Suspend) Resume On RTC Alarm : Disabled RTC Alarm Date : 15 RTC Alarm Hour : 12 RTC Alarm Minute : 30 RTC Alarm Second : 30 ESC: Quit ^v> <: Select Item F1 : Help PU/PD+/-/ : Modify F5 :Old Values (Shift)F2:Color F6 : Load BIOS Defaults F7 : Load SETUP Defaults Figure 5: Power Management Setup • •••• ACPI Standby State S1/POS Set ACPI Standby State to S1/POS (Power On Suspend). (Default value) S3/STR Set ACPI Standby State to S3/STR (Suspend To RAM). • •••• USB Dev Wakeup From S3-S5 USB Device Wakeup From S3 can be set when ACPI Sleep Type se...