Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Материнские платы - GA-8PE667 Pro (3.16 mb)
Материнские платы - GA-8PE667 Pro (11.64 mb)
Фрагмент инструкции
11)RAM_LED • Do not remove memory modules while DIMM LED is on. It might cause short or -+ other unexpected damages due to the 2.5V stand by voltage. Remove memory modules only when AC Power cord is disconnected. 12) PWR_LED • PWR_LED is connect with the system power indicator to indicate whether the system is 1 MPD-on/off. It will blink when the system enters MPD-suspend mode. MPD+ If you use dual color LED, power LED will turn to another color. GA-8PE667Ultra /Pro Motherboard - 20 EnglishEnglish 13)AGP_LED - + 14)IR/CIR (IR/CIR ) IRTX GND NC GND VCC IRRX CIRRX NC NC VCC 1 15)F_USB1/F_USB2/F_USB3(**)/F_USB4(**) (Front USB Connector, Yellow Connector) • When an AGP 2x (3.3V) card is installed the AGP_LED will light up, indicating a non-supported graphics card is inserted. Informing users that system might not boot up normally due to AGP 2x (3.3V) is not supported by the chipset. • Make sure the pin 1 on the IR device is aling with pin one the connector. To enable the IR/CIR function on the board, you are required to purchase an option IR/ CIR module. For detail information please contact your autherized Giga-Byte distributor. To use IR function only, please connect IR module to Pin1 to Pin5. • Be careful with the polarity of the front USB connector. Check the pin assignment while you connect the front USB cable. Please contact your nearest dealer for Power Power USB Dx- USB Dy- USB Dx+ USB Dy+ GND GND USB Over Current optional front USB cable. 1 16)WOL(Wake on LAN) • This connector allows the remove servers to manage the system that installed this mainboard via your network adapter which 1 Signal also supports WOL. +5V SB GND -21 -Hardware Installation Process EnglishEnglish 17)SD(Secure Digital Memory Card Interface,Red exide Connector) (**) 18)SCR(Smart Card Interface,Black Connector) 19)MS (Memory Stick Interface,White Connector) (**) SCR 5 SCAPSNT SCACLK SCAC8 SCAIO SCALED SCAC4 SCARST SCAPWCTL VCC 1 MS GND MSLED MSPWCTLMSCLK MS5 MS4 MS3 MS2 VCC3 MS1 1 GND 20)SPDIF (SPDIF Out) GND SPDIF Out 1 VCC 21)SPDIF_IN GND SPDIF IN 1 VCC • The device could be expanded for reading Flash Memory, such as SD(Security Digital), MS (Memory Stick) and Smart Card Reader Connector. The Smart IC Card could increase security in authenticating online transactions; the card reader device ( inquire local distributor) made by Third Party could be purchased by users. SD SDLED SDPWCTLSDCLK SD5 SD4 SD3 SD2 VCC3 SD1 1 GND • The SPDIF output is capable of providing digital audio to external speakers or com pressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. • Use this feature only when your stereo system has digital output function. * For GA-8PE667 Pro Only. ** For GA-8PE667 Ultra Only. GA-8PE667Ultra /Pro Motherboard - 22 EnglishEnglish 22)F_AUDIO (F_AUDIO Connector) Front Audio (L) Rear Audio (L) Reserved Rear Audio (R) Front Audio (R) POWER REF GND MIC 1 23)CD_IN (CD Audio Line In Connector) CD_L • If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer. • Connect CD-ROM or DVD-ROM audio out to the connector. GND 1 CD_R 24)AUX_IN ( AUX In Connector) • Connect other device(such as PCI TV Tunner audio out )to the connector. AUX-R GND 1 AUX-L 25)SUR_CEN • Please contact your nearest dealer for optional SUR_CEN cable. SUR OUT(R) 1 2 BASS_OUT CENTER_OUT SUR OUT(L) GND -23 -Hardware Installation Process EnglishEnglish 26)CI • This 2 pin connector allows your system to enable or disable the system alarm if the sys GND tem case begin remove. Signal 1 27)BATTERY (Battery) CAUTION • Danger of explosion if battery is incorrectly replaced. + • Replace only with the same or equivalent type recommended by the manufacturer. • Dispose of used batteries according to the manufacturer’s instructions. GA-8PE667Ultra /Pro Motherboard - 24 English English - 25 -Memo English English GA-8PE667Ultra /Pro Motherboard - 26 Chapter 3 BIOS Setup Chapter 3 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP After power on the computer,pressing immediately during POST (Power On Self Test)itwil llal llowyouto enter standard BIOS CMOS SETUP. If you require more advanced BIOS settings, please go to “Advanced BIOS” setting menu.To enter Advanced BIOS setting menu, press “Ctrl+F1” key on the BIOS screen. CONTROL KEYS <..> <..> Move to previous itemMove to next item <..> Move to the item in the left hand <..> Move to the item in the right hand