Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Материнские платы - GA-8IPE1000 Pro3 (258.54 kb)
Материнские платы - GA-8IPE1000 Pro3 (4.11 mb)
Фрагмент инструкции
2 (1) Installing SATA hard drive(s) in your system ............................................................................. 2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup .................................... 3 (3) Configuring RAID set in RAID BIOS ............................................................................................. 5 (4) Making a SATA controller driver disk .......................................................................................... 8 (5) Installing SATA controller driver during OS installation ............................................................ 10 Ac Configuring SATA Hard Drive(s) (Controller: Intel ICH5R) Ae To set up SATA hard drive(s), you have to follow the steps below: ¤¤ (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. ¤a (3)* Configure RAID set in RAID BIOS. (4) Make a floppy diskette containing the SATA controller driver. (5) Install the SATA controller driver during OS installation. Before you begin Please prepare: (a) Two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID with the SATA controller, you may prepare only one hard drive. (b) An empty formatted floppy disk. (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard. (1) Installing SATA hard drive(s) in your system Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard (If there are more than one SATA controllers on your motherboard, you may check the name of the SATA connector to identify the SATA controller for the connector. For example, the SATA0_SB/SATA_SB connectors is controlled by the SATA controller on South-Bridge). Then connect the power connector from your power supply to the hard drive. SATA Hard Drive Configurations ( Intel ICH5R) -2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup You have to make sure whether the SATA controller is configured correctly in system BIOS Setup and set BIOS boot sequence for the SATA hard drive(s). Step 1: Turn on your computer and press the Del key to enter BIOS Setup during POST (Power-On Self Test). To use the SATA controller, assure that the On-Chip SATA item under the Integrated Peripherals menu is set to Auto or Manual. Set SATA RAID Function to Enabled if you want to create RAID (Figure 1). Set the option to Disabled if you do not want to create RAID. CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Integrated Peripherals • ........: Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F6: Fail-Safe Defaults F7: Optimized Defaults Figure 1 -3 -SATA Hard Drive Configurations ( Intel ICH5R) Ac Step 2: Select Hard Disk Boot Priority under the Advanced BIOS Features menu and then choose the modelAe of the SATA hard drive onto which you want to install Microsoft Windows 2000/XP (Figure 2). ¤¤ ¤¤ CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Hard Disk Boot Priority ¤a ..• • • ..• • Figure 2 Step 3: Set First Boot Device under the Advanced BIOS Features menu to CD-ROM to boot from CD-ROM after system restarts (Figure 3). CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Advanced BIOS Features • ........: Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults • Figure 3 Step 4: Save and exit BIOS Setup. SATA Hard Drive Configurations ( Intel ICH5R) -4 (3) Configuring RAID set in RAID BIOS To configure a RAID array, you have to enter the RAID setup utility. Skip this step and proceed to Section 4 on page 8 if you do not want to create RAID. After the Power-On Self-Test (POST) memory test begins and before the operating system boot begins, look for a message which says "Press