Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
2.0) Motherboard - 10 English Rear Panel I/O • 1 PS/2 keyboard port • 1 PS/2 mouse port • 1 parallel port • 1 serial port (COMA) • 1 VGA port • 4 USB 2.0/1.1 ports • 1 RJ-45 port • 3 audio jacks (Line In / Line Out / MIC In) I/O Control • IT8705 chip Hardware Monitor • System voltage detection • CPU temperature detection • CPU / System fan speed detection • CPU smart fan control BIOS • 1 4Mbit flash ROM • Use of licensed AWARD BIOS Additional Features • Supports @BIOS • Supports Download Center • Supports Q-Flash • Supports EasyTune (only supports Hardware Monitor function)(Note 2) • Supports Xpress Install • Supports Xpress Recovery2 • Supports Xpress Rescue Bundle Software • Norton Internet Security (OEM version) Form Factor • Micro ATX form factor; 24.4cm x 23.0cm (Note 1) For further CPU support information, please go to GIGABYTE's website. (Note 2) EasyTune functions may vary depending on different motherboards. -11 -Hardware Installation English Fig. 3 Fig. 4 Notice the small gold Once the CPU is colored triangle lo- properly inserted, cated on the edge of please replace the the CPU socket. plastic covering and Align the indented cor push the metal lever ner of the CPU with back into its original the triangle and gently insert the CPU into position. position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.) 1-3 Installation of the CPU and Heatsink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2 . Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and heatsink. 4. Please make sure the heatsink is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur. 5. Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. HT functionality requirement content : Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components: - CPU: An Intel® Pentium 4 Processor with HT Technology - Chipset: An SiS® Chipset that supports HT Technology - BIOS: A BIOS that supports HT Technology and has it enabled - OS: An operation system that has optimizations for HT Technology 1-3-1 Installation of the CPU Metal Lever Fig. 1 Fig. 2 Gently lift the metal Remove the plastic lever located on the covering on the CPU CPU socket to the socket. upright position. GA-8S661FXM-775(rev. 2.0) Motherboard - 12 1-3-2 Installation of the Heatsink English Fig.1 Please apply an even layer of heatsink paste on the surface of the installed CPU. Male Push Pin The top of Female Push Pin Female Push Pin Fig. 2 (Turning the push pin along the direction of arrow is to remove the heatsink, on the contrary, is to install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan) Fig. 3 Fig. 4 Place the heatsink atop the CPU and make sure Please make sure the Male and Female push pin the push pins aim to the pin hole on the are joined closely. (for detailed installation motherboard.Pressing down the push pins instructions, please refer to the heatsink installation diagonally. section of the user manual) Fig. 6 Fig. 5 Finally, please attach the power connector of the Please check the back of motherboard after heatsink to the CPU fan header located on the installing. If the push pin is inserted as the picture, motherboard. the installation is complete. The heatsink may adhere to the CPU as a result of hardening of the heatsink paste.To prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heatsink. -13 -Hardware Installation GA-8S661FXM-775(rev. 2.0) Motherboard - 14 - English Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2 . Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage. 3 . Memory modules have a foolproof insertion design. A memory module can be i...