Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Before connecting the power connector, please m ake sure that all com ponents and devices are properly installed. Align the power connector with its proper location on the m o therboard an d connect tightly. The AT X_12V powe r connecto r m ainly s upplies po wer to the CPU. If the ATX_12V power conne ctor is not connected, the syste m will not start. Caution! Please u se a power sup ply that is able to handle th e system voltag e requirem ents . It is recom m ended that a power supply th at can withstand high power consum ption be u sed (300W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable system or a system that is unable to start. Please rem ove the sticker on the m otherboard before plugging in while the ATX power supplier is 24 pins; Other wise, please do not rem ove it. 1 3 2 4 1 3 1 2 4 1 2 Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V Pin No. Definition 1 3. 3V 2 3. 3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5V SB(s tand by + 5V) 10 +12V 11 +12V 12 3.3 V(Only for 2 4pins AT X) 13 3. 3V 14 -12V 15 GND 16 PS_ON(sof t On/Off) 17 GND 18 GND 19 GND 20 -5 V 21 VCC 22 VCC 23 VCC 24 GND English -19 -Hard ware In stalla tion EnglishEnglish 3/4) CPU_FAN / SYS_FAN (Cool er Fan Power Co nnector) The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a ful-proof con nection design. M ost coolers are designed with colo r-coded power connecto r wires. A red power co nnector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the gr ound wire (GND). Please rem em ber to connect the powe r to the cooler to prev ent system overheating and failure. Caution! Please rem em ber to c onnect the po wer to the CP U fan to pre vent CPU over heating and failure. 1 1 CPU_ FAN SYS_ FAN Pin No. Definition 1 GND 2 +12V 3 Sense 4 Speed Control (On ly for CPU_FAN) 5) IDE1/ IDE2 (ID E Connec tor) An IDE dev ice connects to the com puter via an IDE connector. One IDE connector can conn ect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard d rive or optical drive). If you wish to connect two IDE devices, please set th e jum per on one IDE device as M aster and the other as Slav e (for infor m ation on se ttings, plea se refer to the instructions located on the IDE d evice). 12 3 9 4 0 GA-8IP775 Series M otherboard -20 6) FDD (Floppy Connector) The FDD connector is used to co nnect the FD D cable while the other e nd of the ca ble connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2M B, 1.44M B and 2.88M B. Please connect th e red powe r connector wire to th e pin1 pos ition. 12 3 3 3 4 7) SATA0/SATA1 (Serial ATA C onnector) Serial ATA can prov ide 150M B/s transfer rate. Please re fer to the B IOS setting for the Serial ATA and install th e proper driver in order to work properly. 7 1 Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND English -21 -Hard ware In stalla tion EnglishEnglish 8) PWR_LED PWR_ LED is c onnect with the system power indicator to indicate wh ether th e syste m is on/ off. It will blin k when the system enters suspend m ode. 1 Pin No. Definition 1 M PD+ 2 M PD3 M PD 9) F_PANEL (Front Panel Jumper) Please connect the power LE D, PC peak er, reset s witch and p ower switc h etc of yo ur chassis front panel to the F_PAN EL connecto r according to the pin assignm ent below. 12 1 9 2 0 H D H D+ RES+ RE SNC SPEAKM SGM SG+ PW PW + SPEAK+ Me ssa g e L E D/ Po we r/ Sle e p L ED Po we r S wit ch Sp e a ke r C o n n e c to r ID E H a rd Di sk Ac ti ve L ED Re se t S wit ch HD ( IDE Har d Disk Ac tive LED) (Blue) Pin 1 : LED ano de(+) Pin 2: LED c athode(-) SPEAK ( Speaker Conn ec tor) (Am ber) Pin 1: VCC (+) Pin 2-Pin 3 : NC Pin 4: Dat a(-) RES (Rese t Switc h) (Green) Open: Norm al Operation Close: Reset H ardware System PW (Power Switc h) (Red) Open: Norm al Operation Close : Power O n/Off M SG(M essage LED/Power/Sleep LED) (Yellow) Pin 1 : LED ano de(+) Pin 2: LED c athode(-) NC( Pu rple) NC GA-8IP775 Series M otherboard -22 10) F_AUDIO (Front A udio Connector) If you wa nt to use Front Audio connector, you m ust rem ove 5-6, 9-10 Jum per. In order to utilize the front audio header, your chassis m us t have front audio conn ector. Also please m ake sure the pin assigm ent on the cable is the sam e as the pin assigm ent on the M B head er. To find out if the chassis you are buying support front audio connector, please contact your dealer.Please note, you can have the alternative of using front audio connector or of using rear aud io connector to play sound. 2 91 0 1 Pin No. Definition 1 MIC 2 GND 3 M IC_BIAS 4 POWER 5 FrontAudio(R) 6 RearAudio(R) 7 Reserved 8 No Pin 9 FrontAu dio (L) 10 RearAudio(L) 11) SUR_ CEN Please contact your nearest dea ler for optional SUR_CEN cable. 1 2 7 8 Pin No. Definition 1 SUROUT L 2 SUROUT R 3 GND 4 No Pin 5 CENTER_OUT 6 BASS...