Never let any facilitate the collection of spent nickel-cadmium batteries. Help (30cm) of line to ensure that tool performance. liquid get inside the tool; never immerse any part of the tool into a liquid. protect our environment and conserve natural resources by it is undamaged. If it is OK returning the spent nickel-cadmium battery to an authorized rewind it and insert the line ACCESSORIES To install bulk line, follow the steps below. Black & Decker service center or to your local retailer for

If the plug still does not fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The table shows the correct size to use depending

Longest life and best performance can be obtained if the batteries are charged at normal room temperatures. 2. While charging, the charger will normally become warm to the touch. 3. If the batteries do not charge properly : a. Check house current at receptacle by plugging in a lamp or other appliance. b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. c. If house current is okay and you do not get proper charging, contact your nearest

of Schiller-Pfeiffer Inc. All Rights Reserved. Owners Manual and Safety Instructions Table of Contents Important Information Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Service Information . . . . . . . . . . . . . . . . . . . . .1 Special Safety Information . . . . . . . . . . . . . . . .1 Safety and Warnings Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . .2 General Safety Rules . . . . . . . . . . . . . . . . . . . .3 Important Information A. Introduc

MOUNTING THE CHARGER BRACKET 1. If you intend to mount, the charger bracket on a wall, follow the instructions listed below. 2. Remove the two screws and plastic anchors from the plastic bag. 3. Use the charger bracket to mark the locations of the holes required. Be sure to mount the bracket high enough so that the trimmer can hang freely from it; about 4 feet (1.2m) from the floor. 4. Drill a .250” (6 mm) diameter hole at each marked location. 5. Insert the plastic anchors into the holes and in

C WARNING: Do not charge the battery at ambient temperatures below 36° F (2°C) or above 104°F (40°C). Recommended charging temperature: Approximately 75°F (24°• Note: The charger plug incorporates lock outs to prevent the use of incorrect chargers. The plug must be correctly oriented when inserted. • Insert the charger plug into the charger connector at the rear of the tool (fig. D) . • Plug the charger into a 120V outlet. • Charge the tool for 16 hours before first use. For catalog numbers GSL3

On/off switch 2. Lock-off button 3. Blade release button 4. Grass Shear blade (GSL35, GSL75, GSN30, GSN35) 5. Shrub Trim blade (GSL35, GSL75, GSN32, GSN35) 6. Blade cover (not shown) Assembly WARNING: Avoid accidentally switching the tool on 52143during assembly. Fitting and removing the blade (fig. A, B, C) The shear blade (4) has been designed for trimming grass and weeds. The trim blade (5) has been designed for trimming hedges and shrubs. • To remove the blade cover (6). Push and hold the bl

Our aim is to provide quality tools at an affordable price. We hope that you will enjoy using this tool for many years. EC DECLARATION OF CONFORMITY GT20/GT25 Black & Decker declares that these products conform to: 98/37/EC, 89/336/EEC, 73/23/EEC, BS 2769 (EN 50144 not including 23.5), EN 55014, EN 61000, 2000/14/EC, Hedge trimmer . 330 W, Annex V Level of sound pressure, measured according to 2000/14/EC: GT20 GT25 LpA (sound pressure) dB(A) 81 81 LWA (acoustic power) dB(A) 94 94 LWA (guaranteed

2. While charging, the charger will normally become warm to the touch. 3. If the batteries do not charge properly: a. Check house current at receptacle by plugging in a lamp or other appliance. b. Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. c. If house current is okay and you do not get proper charging, contact your nearest Black & Decker Service Center. 4. The grass shear should be recharged when it fails to produce sufficient po

to 5 p.m. EST Mon. -- Fri. to speak with an agent. Please have the catalog number available when you call. for instant answers 24 hours a day. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. BLADE ATTACHMENT - SHRUBBER COMBO ONLY! (SSC1000) (FIG 9 AND 10) The SSC1000 has two interchangeable cutting heads, the Shrubber head and t